Water Treatment; Filter Media - Exo Terra Cascade PT3590 Instrucciones De Uso

be placed horizontally or flat on the bottom; in aqua-terrariums,
because of higher water levels, the filter pump could be placed
horizontally or vertically). If in doubt, consult with your local Exo
Terra dealer or pet retailer for more information.
®
Install the filter pump in the desired location, ensuring that the
water flow output (located on the top of the pump) is below the
water surface. Press firmly to ensure the suction cups are holding it
securely in place. Ensure that the water does not contain particulate
matter that may enter the filter pump and damage the impeller or
block its shaft.
The filter pump is equipped with a 90° and 180° spout to connect
tubing to create waterfalls up to a height of 180 cm. Also included:
a 90° swivel spout which directs the water flow output and allows
changes to the flow pattern in the terrarium.
Connect the power cord to the electrical outlet. If the unit does not
start immediately, verify that the water level is sufficient to immerse
the filter pump's water flow outlet during operation. If the problem
persists, see the "Trouble-shooting" and "Maintenance" sections of
this manual for further information.

WATER TREATMENT

The water should be treated with Exo Terra
chlorine and heavy metals. Adding Exo Terra
keep the water cleaner longer, as well as promoting necessary
beneficial bacteria and reducing odors associated with
decaying waste.
Maintenance
To avoid injury, always unplug all appliances from the outlet when
6
not in use; before putting on or taking off parts; and before cleaning.
The motor is hermetically sealed, thereby requiring no lubrication
or maintenance.
The impeller cavity, although it is self cleaning, requires regular
maintenance to remove dirt, slime and debris build-up to ensure
smooth running and to extend the life of the pump. The impeller and
impeller well (where the impeller is located) should be cleaned at
least once a month, more often if necessary.
Cleaning the impeller:
1. Unplug the pump and remove it from the installation.
2. Separate the filter case from the motor housing
3. Use a screw driver to remove the impeller cover.
4. Remove the plastic ring on top of the impeller fan.
5. Grasp the blades of the impeller fan to pull out the impeller
6. Thoroughly clean the impeller and the impeller well to remove
slime, dirt or debris.
7. Place the impeller back into the impeller well. Replace the plastic
ring and the impeller cover, then re-attach the filter case to the
motor housing.
Note: If you are using well water, or if you have hard water, run the
filter for a few minutes in a 50/50 solution of water and vinegar to
help remove calcium deposit buildup before replacing the filter in
the installation.
CAUTION: Do not use detergents or other chemical cleaners. The
power cord cannot be replaced, discard the appliance if damaged.
FILTER MEDIA: The Exo Terra
Aquatize to remove
®
Biotize will help to
®
Cascade High Performance Pump
®
HP180 provides 3-stage filtration. The large foam captures and
removes large particulate matter and debris and enhances biological
filtration, the smaller foam captures smaller, finer particulate matter;
and the carbon cartridge helps improve water clarity, color
and smell.
The foam pads will gradually fill with trapped debris and require
rinsing. Re-using the foam can help protect the bacterial colonies
and provide continual biological filtration. Foam pads should be
rinsed at least once a month, more often if necessary.
It is not recommended to rinse the foam directly in tap or well water,
as the water contains chemicals that make it unsafe to reptiles and
amphibians. As a precaution, the foam should always be rinsed
in de-chlorinated water. To do this, fill a container with water and
then treat the water with a water conditioner such as Exo Terra
Aquatize to neutralize the chemicals. Once the water has been
de-chlorinated, you can then rinse the foam. (note: this procedure is
also recommended when replacing with new foam).
Filter media (foam pads, carbon cartridge) should be replaced every
6-8 weeks to ensure proper functioning of the filter, more often if
necessary. Never rinse or replace all filter media at the same time,
alternate rinsing/replacement of filter media.
Replacement Filter Foam and Carbon cartridges can be purchased
from your local Exo Terra dealer or pet retailer.
®
Troubleshooting:
CAUTION: The pump must not be allowed to run dry. If the pump
fails to operate, check the following:
No Flow:
• Check if the power supply is on. Check the circuit breaker or try
another outlet to ensure the pump is getting electrical power.
Note: always disconnect the pump from electrical supply
before handling.
• If the power supply is working but the pump is not, then it may
be clogged by debris. Disconnect the pump, check the output
spout to ensure it is not clogged, then follow the maintenance
procedures to clean the impeller.
• If the pump is working but there is no flow, remove filter basket
and the tubing from the pump house and let the pump run until
the flow is up to standard again. Replace the filter basket and
check if the flow is still up to standard. If not, repeat the first step.
Connect the tubing to the pump.
Low Flow:
• Check the pump's output spout to ensure it is not clogged by
debris. Then follow the maintenance procedures to clean impeller.
• When using tubing, check tubing for sharp bends or blockage.
• If the pump is working but there is only a low flow, remove filter
basket and the tubing from the pump house and let the pump run
until the strength of the flow is up to standard again. Replace the
filter basket and check if the flow is still up to standard. If not,
repeat the first step. Connect the tubing to the pump.
®