Functional Description; Removing/Inserting The Battery - Milwaukee MXF-301 Manual Del Operador

• Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.

FUNCTIONAL DESCRIPTION

2
1
13
11
14
12
1. Spindle
2. Speed selector
3. Command Center
4. Arm button
5. Trigger Lock
6. Trigger
7. Handle
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
CAUTION
Read operator's manual
Always wear eye protection.
Use appropriate hearing and
respiratory protection.
UL Listing for Canada and U.S.
C US
3
10
9
8. Water quick connect
9. Water valve
10. Side handle locations
11. Worklight
12. Battery latch lock
13. Battery latch lever
14. Side handle
Risk of Electric Shock
SPECIFICATIONS
Cat. No. ..................................................MXF301-0
Battery Type ........................................ MX FUEL™
Charger Type....................................... MX FUEL™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
No Load RPM .............................. 0 - 800 / 0 - 1600
Max. Bit Capacity................................................. 6"
Spindle Thread .........................................1-1/4" - 7
5/8"-11 Spindle Adapter ........................ 48-17-6005
Max. Inlet Pressure........................................90 psi
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push the battery latch lock
4
to the side and squeeze the battery latch lever. Pull
the battery pack away from the machine.
WARNING
5
6
To insert the battery, slide the pack into the body of
the machine. Make sure it latches securely into place.
7
WARNING
Others may be hazardous.
Selecting and Installing a Core Bit
8
MILWAUKEE offers core bits that are designed to
cut through a variety of materials including poured
concrete, steel-reinforced concrete, and prestressed
concrete. Select the proper style and size bit for the
job. Always use clean, sharp, and properly main-
tained bits. Use core drill bits with a 1-1/4"-7 thread.
Bits with a 5/8"-11 thread can be used with adapter
48-17-6005.
1. To install the bit, remove the battery pack.
2. Thread the bit securely onto the spindle.
3. Grip collar tightly (by hand or with a 1-1/4" open
end or adjustable wrench) and tighten the bit
securely.
4. To remove bit, remove the battery pack.
5. Place a 1-1/4" open end or adjustable wrench
on the collar, and a 1-3/4" or adjustable wrench
on the bit.
6. Hold the collar wrench securely while using the bit
wrench to loosen the bit.
Diamond Core Bits
The following conditions can greatly influence dia-
mond core performance:
• Amount of water
• RPM of core drill motor
• Bit runout
• Amount of steel
• Size of embedded steel
• Age of concrete
• Aggregate (size, type, hardness, abrasiveness)
• Type of sand–manufactured vs. river (natural)
• Operator technique
• Operator care
• Feed pressure applied to bit by operator
• Core Drill Stand rigidity and condition
4
ASSEMBLY
Recharge only with the charger
specified for the battery. For spe-
Always remove battery pack before
changing or removing accessories.
Only use accessories specifically
recommended for this machine.