IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F).
Let a hot battery cartridge cool down before
charging it.
4.
Charge the battery cartridge once in every six
months if you do not use it for a long period of
time.
FUNCTIONAL DESCRIPTION
ENC007-7
Installing or removing battery cartridge (Fig. 1 &
2)
CAUTION:
• Always switch off the tool before installing or removing
the battery cartridge.
• Make sure that you lock the battery cover before use.
Otherwise, mud, dirt, or water may cause damage to
the product or the battery cartridge.
To install the battery cartridge;
1.
Pull the battery cover locking lever toward yourself
and open the battery cover.
2.
Insert the battery cartridge in the direction shown in
the figure until a click is heard.
3.
Insert the lock key in the place shown in the figure
as far as it will go.
4.
Close the battery cover and push it on until it is
latched with the locking lever.
To remove the battery cartridge from the mower;
1.
Pull the battery cover locking lever toward yourself
and open the battery cover.
2.
Pull out the lock key.
3.
Withdraw it from the tool while sliding the button on
the front of the cartridge.
4.
Close the battery cover.
Battery converters (optional accessory)
WARNING:
• Before installing or removing the battery converters
BCV01/BCV02, remove the lock key.
BCV01 (optional accessory) (Fig. 3, 4 & 5)
WARNING:
• When using the BCV01, never attach it to any part of
your body. Attaching the BCV01 to any part of your
body may cause a serious injury.
Slide the battery converter BCV01 into the installation
hole until it stops.
Open out the battery cover on the mower and then slide
all the way and click the product mounting adapter of the
BCV01 into the battery port on the mower.
Run the cord of the BCV01 through the slit in the battery
cover and close the battery cover.
Fit the cord of the BCV01 into the upper holders on the
handle.
NOTE:
• When using the battery converter BCV01 (optional
accessory), hook the power cord to the designated
holder on the mower. Failure to do so may cause the
cord to be cut off.
To remove the BCV01 from the mower, open out the bat-
tery cover and then press the hook on the battery mount-
ing side of the BCV01.
BCV02 (optional accessory) (Fig. 6 & 7)
Open the battery cover and click in the BCV02 into the
battery port on the mower.
Close the battery cover.
To remove the BCV02, press on the hook of the BCV02
and withdraw it with both hands.
19