Additional Safety Rules For Chain Saw - Dolmar AS-1212 Manual De Instrucciones

8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
ADDITIONAL SAFETY RULES
FOR CHAIN SAW
1. Don't expose chain saw to rain. Don't use it in
damp or wet locations.
2. Hold the chain saw firmly with both hands when
the motor is running.
3. Install saw chain properly according to this
instruction manual.
4. Do not overreach. Keep proper footing and bal-
ance at all times.
5. Keep all parts of the body away from the saw
chain when the motor is operating.
6. Before you start the saw, make sure the saw
chain is not contacting anything.
7. Switch off the chain saw immediately if you
notice anything abnormal in operation.
8. Carefully inspect the chain saw if you drop or
strike it against something hard.
9. When not in use, chain saws should be stored in
a dry, and high or locked-up place — out of
reach of children. When storing saw, use a scab-
bard (chain cover).
10. Use safety glasses. Also use safety footwear;
snug fitting clothing; protective gloves; and
head protection.
Charging (Fig. 2)
Plug the battery charger into the proper AC voltage source. The charging light will flash in green color. Insert the bat-
tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective
markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When
the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The
charging light will remain lit steadily during charging. When charging is completed in approx. 45 minutes, the charging
light color will change from red to green.
After charging, unplug the charger from the power source.
Battery type
AP-123
CAUTION:
• The battery charger is for charging Dolmar battery cartridge. Never use it for other purposes or for other manufac-
turer's batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location
exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a
while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the
battery cartridge from the battery charger.
• If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The ter-
minals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.
10
11. Before making a cut, remove dirt, stones, loose
bark, nails, staples and wire from the tree.
12. Secure the workpiece so that it will not move
suddenly during operation. Be careful of cut-off
pieces. They may hit operator.
13. To prevent the saw chain from being pinched in
the cut, support the workpiece near the cut
using blocks or the like.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the car-
tridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around
you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Capacity (Ah)
2.0
Number of cells
10