EINHELL TC-SM 216 Manual De Instrucciones página 30

and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
Warning! To make 0°-45° miter cuts (with the ma-
chine head (4) inclined or the turntable set at an
angle), the adjustable stop rail (14) must be fi xed
at an outer position.
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
6.1 Cross cut 90° and turntable 0° (Fig. 1-3,
11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (29) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (29)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (13) and on the turntable (19).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Press the release button (3) to release the
On/Off switch (2).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull the
machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the
very back until the saw blade (7) has comple-
tely cut through the workpiece.
Anl_TC_SM_216_SPK9.indb 30 Anl_TC_SM_216_SPK9.indb 30
GB
•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 12)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Swing up the machine head (4).
•
Move the locking lever (20) to its top position
to enable the turntable to be adjusted.
•
While holding the release button (21) pressed
down, turn the turntable (19) and scale poin-
ter (22) to the desired angular setting on the
scale (23).
•
To lock the turntable (19), press the locking
lever (20) down.
•
Cut as described in section 6.1.
6.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 13)
The crosscut saw can be used to make miter cuts
of 0- 45° in relation to the work face.
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (19) in 0° position.
•
Release the locking grip (26) and tilt the
machine head (4) to the left until it coincides
with the required angular setting on the scale
pointer (24) on the scale (25). Then secure
the locking grip (26) again.
•
Cut as described in section 6.1.
6.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 14)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
Move the machine head (4) to its upper po-
sition.
•
Move the locking lever (20) to its top position
to enable the turntable to be adjusted.
•
While holding the release button (21) pressed
down, turn the turntable (19) and scale poin-
ter (22) to the desired angular setting on the
scale (23).
- 30 -
24.04.2019 09:30:48 24.04.2019 09:30:48