Quick Start - NEC MultiSync LCD175VXM+ Manual Del Usuario

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any
kind of contact with any part inside this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this
unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
Contents
Cable management
Power
User's Cord
Manual CD-ROM
Audio 15-pin mini D-SUB
Cable male to 15-pin mini
D-SUB male

Quick Start

Figure 1
Figure A.1 Figure A.2
Stand
Base
Figure A.4
AUDIO INPUT
Figure B.1
01_English
WARNING
cover
DVI-D to DVI-D
(LCD195VXM+
MultiSync LCD monitor
only)
Figure 2
Macintosh Cable Adapter (not included)
Figure A.3
Cable management cover
DVI-D (Input2)
D-Sub (Input1)
Cable management cover
Connect to Computer
audio output
English-1
1
Declaration of the Manufacturer
We hereby certify that the colour monitors MultiSync LCD175VXM+
(L174F1)/LCD195VXM+ (L194F2) are in compliance with
Council Directive 73/23/EEC:
– EN 60950-1
Council Directive 89/336/EEC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
Your new NEC MultiSync LCD monitor box* should contain the
following:
• MultiSync LCD monitor with tilt base
• Audio Cable
• Power Cord
• Video Signal Cable (15-pin mini D-SUB male to 15-pin mini
D-SUB male)
• Video Signal Cable (DVI-D to DVI-D) (LCD195VXM+ only)
• User's Manual
• CD-ROM
• Cable management cover
* Remember to save your original box and packing material to transport or ship
the monitor.
To pull the stand, follow these instructions:
1. Place monitor face down on a non-abrasive surface (Figure 1).
2. Pull the stand holding the monitor with the other hand until the
stand clicks (Figure 2).
NOTE: Handle with care when pulling the stand.
NOTE: Reverse this procedure if you need to re-pack the monitor.
To attach the MultiSync LCD monitor to your system, follow these
instructions:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI-D
signal cable to the connector of the display card in your system
(Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB
signal cable to the connector of the display card in your system
(Figure A.2). Tighten all screws.
For the Mac: Connect the MultiSync Macintosh cable adapter
(not included) to the computer. Attach the 15-pin mini
D-SUB signal cable to the MultiSync Macintosh cable adapter
(Figure A.3). Tighten all screws.
NOTE: Some Macintosh systems do not require a Macintosh cable
adapter.
3. To attach the Cable management cover:
Insert the tabs of the Cable management cover into the holes of
Stand neck and slide the Cable management cover downward into
place (Figure A.4).
NOTE: Please confirm that the tabs are completely secure.
4. Connect all cables to the appropriate connector on the back of the
monitor (Figure B.1). Connect the Headphone (not included) to
the appropriate connector at the rear side of the monitor (Figure
C.1).
10/1/07, 1:06 PM
and marked with
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan