Intended Use; Assembly And Adjustments - Black+Decker YARDMASTER Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
Recharge discharged batteries as soon as possible
after every use.
Do not discharge batteries fully.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger.
3. The green LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
Charger Cleaning Instructions

WARNING:
the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the
charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
6
Shock hazard. Disconnect
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING:
tool or any part of it. Damage or personal injury
could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

Your sweeper attachment is designed for
homeowner applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this appliance.

ASSEMBLY AND ADJUSTMENTS


WARNING:
serious personal injury, turn unit off and remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Tube Assembly (Fig. B)
nOTE: Ensure the sweeper is switched off and the battery
is removed before attaching or removing the sweeper tube.
The tube must be assembled to the housing before use.
1. To attach the tube to the sweeper, line up the tube with
the sweeper housing as shown in Fig. B.
2. Push the tube into the sweeper housing until the lock
button 
12
engages the lock hole 
Never modify the power
To reduce the risk of
13
in the tube.

Publicidad

Tabla de contenido
loading

Productos relacionados para Black+Decker YARDMASTER

Este manual también es adecuado para:

Bcasbl70

Tabla de contenido