Instalation Instructions - JB Systems Light LED STRING WHITE Manual De Instrucciones

ENGLISH

INSTALATION INSTRUCTIONS

! IMPORTANT NOTICE ! NEVER disconnect any parts or make any change in the setup while the
installation is connected to the mains: some parts could be seriously damaged!
THE SIMPLE WAY
If you only want to use the standard "plug & play" starter set, things are VERY simple: just build the elements
from this "LS-WH-STARTER" starter kit together and connect the complete string to the mains. Installation
finished: no need to look any further! 
THE SOPHISTICATED WAY
Based on the basic "LS-WH-STARTER" set you can build a bigger system, just by adding the optionally
available accessories. For each of these accessories we give a description with possible applications:
LS-POWER-7A
The controller of the "starter set" can control strings with up to 1024 LED-
bulbs, however its internal power supply only supports up to 12 LED-bulbs.
This means that you should add an extra power supply, as soon as you add
extra strings. The LS-POWER-7A power supply can deliver power for up to
116 LED-bulbs. So every 116 LED-bulbs an extra LS-POWER-7A should
be inserted in the line.
The LS-POWER-7A contains a special POWER-T, used to "inject" the extra
power into the line with strings. See the example below to learn how to
insert the LS-POWER-7A:
LS-BUFFER
While adding extra strings, the quality of the control signal
degrades. Adding buffers helps upgrading the control signal
again! Buffers should be used in the following cases:
 When one or more LS-EXTENSION-3M cables are used,
you should add a buffer before the extension cable(s).
You can connect up to max. 8 extension cables together. Never connect 2 buffers to each other, there
should always be at least one LS-WH-STRING between 2 buffers.
 After every 300 LED-bulbs in a line a buffer is needed.
 When 16 stings are used. Practically this means that when two LS-CURTAIN-2M cables are
connected together in one line, a buffer should be inserted before you can connect another two LS-
CURTAIN-2M cables.
Attention: between 2 buffers at least 1 string should be added. So when 4 LS-CURTAIN-2M cables
are used to make a 8M long curtain, you should add an LS-WH-STRING between the first two and the
second two LS-CURTAIN-2M cables.
JB SYSTEMS
®
OPERATION MANUAL
3/28 LED STRING WHITE
ENGLISH
LS-WH-STRING
One LS-WH-STRING contains 4 LED-bulbs and measures 1,5m. You can add one or more strings in one
line until a maximum of 1024 LED-bulbs is reached. Of course you should add extra LS-POWER-7A
power supplies and LS-BUFFER signal buffers where needed!
LS-CURTAIN-2M
An LS-CURTAIN-2M is a 2m long cable containing 8 T-connectors, used to create a
nice LED-curtain.
You can add one or more of these cables in one horizontal line. Theoretically you can
connect up to 256 LS-WH-STRING cables (1024 LED-bulbs) to each of these 8 T-
connectors. Of course you should add extra LS-POWER-7A power supplies and LS-
BUFFER signal buffers where needed!
The picture on the right gives you an idea of such a "curtain application".
LS-EXTENSION-3M
This 3m long cable is used for bridging the distance between two elements in a
setup. For example: bridging the distance between the controller and the first
string. You can connect up to 8 extension cables together to obtain a maximum
length of 24m. Attention: while using 1 or more extension cables in a line, you
should always add a buffer before!
OPERATING INSTRUCTIONS
Once the starter set (or complete installation) is build, simply connect
the setup to the mains. The effect starts working immediately.
The controller contains 16 programs (13 static + 3 audio controlled)
that can be selected quite easily:
 Unscrew the plastic cover (3) and remove the rubber seal (4)
 Use a small screwdriver to turn the program selector switch (5)
GENTLY(!!!) in both directions until the desired program is selected:
 0 Every 15 lamps 1 lamp is continually chasing forward at
medium speed.
 1 Every 15 lamps 1 lamp is continually chasing forward at slow
speed.
 2 Every 15 lamps 1 lamp is continually chasing backward at medium speed.
 3 Every 15 lamps 1 lamp is continually chasing backward at slow speed.
 4 Every 30 lamps 2 lamps are continually chasing forward at fast speed.
 5 Every 30 lamps 2 lamps are continually chasing forward at medium speed.
 6 Every 30 lamps 2 lamps are continually chasing backward at fast speed.
 7 Every 30 lamps 2 lamps are continually chasing backward at medium speed.
 8 Every 50 lamps a train of 14 lamps, using "trail effect" chases forward at fast speed.
 9 Every 50 lamps a train of 14 lamps, using "trail effect" chases forward at medium speed.
 A Every 50 lamps a train of 14 lamps, using "trail effect" chases backward at fast speed.
 B Every 50 lamps a train of 14 lamps, using "trail effect" chases backward at medium speed.
 C Lamps are continually chasing forward & backward, using "trail effect" at medium speed.
 D Music chase 1: Three flashing patterns run in music controlled mode.
 E Music chase 2: Five different chases run in music controlled mode.
 F Music chase 3: Eight different chases run in music controlled mode.
 Put the rubber seal (4) back in place and fasten the plastic cover (3) to assure the selector is well
protected against moisture and dust.
JB SYSTEMS
®
OPERATION MANUAL
4/28 LED STRING WHITE