Hammer Safety Warnings; Residual Risks; Safety Of Others - Stanley SHM5K Manual De Instrucciones

g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.

HAMMER SAFETY WARNINGS

♦ Wear ear protectors. Exposure to noise can cause
hearing loss.
♦ Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
♦ Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
♦ Be certain that the material being drilled does not
conceal electric or gas service and that their locations
have been verified with the utility companies.
♦ Keep a firm grip on the tool at all times. Do not
attempt to operate this tool without holding it with
both hands. Operating this tool with one hand will result
in loss of control. Breaking through or encountering
hard materials such as re-bar may be hazardous as
well. Tighten the side handle securely before use.
♦ Ensure the chisel is secured in place before operating
the tool.
♦ In cold-weather conditions or when the tool has not
been used for a longer period of time, let the tool run
with no load for several minutes before use.
♦ When working above ground level ensure the area
below is clear.
♦ Do not touch the chisel or the parts close to the chisel
immediately after operation, as they may be extremely
hot and cause burns to the skin.
♦ Always direct the power cable to the rear, away from
the chisel.
♦ Do not operate this tool for long periods of time.
Vibration caused by hammer action may be harmful
to your hands and arms. Use gloves to provide extra
cushion and limit exposure by taking frequent rest
periods.
Note: Mains voltage: When connecting to the mains, it is
imperative to verify if the voltage of the mains matches that
of the power tool. If the mains voltage exceeds the voltage
indicated on the power tool, the user may become severely
injured in an accident, and the tool may be damaged. On
the contrary, if the mains voltage is lower than the voltage
required by the tool, the motor may be damaged as a result.
Thus, if it is not possible to verify the voltage, it is imperative
not to plug in to the power source.

RESIDUAL RISKS

Additional residual risks may arise when using the tool
which may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc. In
spite of the application of the relevant safety regulations and
the implementation of safety devices, certain risks cannot
be avoided. These are:
♦ Injuries caused by touching any rotating/moving parts.
♦ Injuries caused when changing any parts, blades or
accessories.
♦ Injuries caused by prolonged use of a tool. When using any
tool for prolonged periods ensure you take regular breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)

SAFETY OF OTHERS

♦ This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
♦ Children should be supervised to ensure that they do
not play with the appliance.
LABELS ON TOOL
The following symbols are shown on the tool along with date
code:
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
V Volts
A Amperes
Hz Hertz
W Watts
min minutes
Alternating
Current
Position of Date Code (FIG. A)
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example:
2016 XX JN
Year of manufacturing
ENGLISH (
Original Instructions)
Direct Current
n No-Load Speed
0
Class II Construction
Earthing Terminal
Safety Alert Symbol
Revolutions or
/min. Reciprocation per
minute
15