Installation; Connect The Inlet Hoses; Instructions - Maytag EPIC z Manual De Uso Y Cuidado

_!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_![[i_i_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_i_!iii!!_!_!_!_!_i!i!{i!_i!_!ji!!_!_!_!_!!i!i!_i_jii!_!_!_!_!_!!!!i[ii_._!ii!ii!!_jjii!_!iiiiji!!_!_!_!_!_!!i!i_}_!_!_!_!_l!l!!!i!!!_ 4_, i!i[ii_!!!!_iiiiii}ii}_!!i_i_}_i_iii_!ii_!!!_iiiiii}_!iji_!_!i_ii!ii!_!_!_!_i!_ii_1!_!_!_i!i!ii!!_iii!i)ii_:i_!_i[ii_i_!!_ _!_i!_!_!_!!i!i!ii!!_ii!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_ ¸
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft
(90 cm) of its final location.
There are 4 blue bolts in the rear panel of the washer that support the suspension system
during transportation. These bolts also retain the power cord inside the washer until the bolts
are removed.
1. Using a 13 mm wrench, loosen each of the bolts.
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt,
including the plastic spacer covering the bolt.
Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in
the couplings.
A B
A. C_;upling
B. Washer
Connect the inlet hosesto the water faucets
Make sure the washer drum is empty.
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the
washen
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the
washen
3. Using pliers, tighten the couplings with an additional two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve. [Damage to the valves can
result.
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord
through the opening of the rear panel and close the hole with the attached cap.
4. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, call your local service center. [b avoid
suspension and structural damage, your machine must be properly set up for relocation by a
certified technician.
10