Insert Batteries - TFA Dostmann RAINMAN Instrucciones De Uso

TFA_No. 47.3004_Anleitung_07_20 14.07.2020
RAINMAN – Wireless rain station with indoor/outdoor temperature
5.2.2 Rain sensor (Fig. 4+5)
F 1: Housing with funnel
F 3: 2 tabs for the housing
F 5: Battery compartment
F 7: Arrows
6. Getting started

6.1 Insert batteries

• Place the instruments on a table at a distance of about 1.5 meters from each other. Avoid being close to
possible sources of interference such as electronic devices and radio equipment.
Rain sensor
• Press the two tabs on each end of the rain sensor and lift off the funnel portion.
• The battery compartment is under the rocker. Firmly squeeze all four tabs and lift the battery compartment off
the base.
• Insert two new AA 1,5 V batteries into the battery compartment. Make sure the polarity is correct.
• Position the battery compartment with the rocker over the base and press down so all four tabs lock in place.
• Position the housing and press down so both tabs lock into place. ATTENTION: Match the corresponding
arrows on the funnel portion and the base.
Temperature transmitter
• Remove the protective film from the display of the temperature transmitter.
• Open the battery compartment of the temperature transmitter and insert two new AA 1,5 V batteries. Make
sure the polarity is correct. The red LED flashes and all segments will be displayed briefly. The current tem-
perature will be displayed. Close the battery compartment again.
Base station
• Remove the protective film from the base station display.
• Open the base station battery compartment and insert two new AA 1.5V batteries. Make sure the polarity is
correct. The device will alert you with a beep and all segments will be displayed for a short moment. Close the
battery compartment again.
6.2 Outdoor values reception
• The base station will scan the outdoor values of both transmitters. The reception symbol of the rain sensor
and "- -" in the outdoor temperature display are flashing. If the reception is successful, the outdoor tempera-
ture and the rainfall amount appear on the base station display. To simulate rainfall values move the rocker.
• If the reception of the outdoor values fails, "- -" appears on the base station display. Check the batteries and
try it again. Check if there is any source of interference.
• You can also start the initialization manually. Hold the RAIN button (for the rain sensor) or the DOWN button
(for the temperature transmitter) on the base station for three seconds. The base station will try to receive the
measured values.
• Press the TX button in the transmitter's battery compartment. The transmission of the outdoor data will take
place immediately.
18
10:05 Uhr Seite 10
F 2: Base
F 4: Rocker
F 6: 4 tabs for the battery compartment
RAINMAN – Wireless rain station with indoor/outdoor temperature
7. Operation
• Press and hold the CLEAR/UP or DOWN button in the setting mode for fast mode.
• The device will automatically quit the setting mode if no button is pressed for 20 seconds.
7.1 Settings
• Press and hold the SET button for three seconds. 24Hr (default) will be flashing. Press the CLEAR/UP or
DOWN button to choose 12 HR or 24 HR system. Press the SET button to make the settings in the following
sequence: Year, month, day, hours, minutes, day-of-week language (default: ENG), temperature unit (default:
°C) and rainfall amount unit (default: mm). Press CLEAR/UP or DOWN button to adjust the settings.
• Confirm the setting with the SET button.
7.1.1 12/24-hour display setting
• In the setting mode you can choose between the 12 - or 24 hour system.
• In the 12 HR system PM (after noon) appears on the display.
7.1.2 Day-of-the week language
• In the setting mode you can choose between the day-of-the week language: English (ENG), French (FRE),
Spanish (ESP).
7.1.3 Temperature unit setting
• In the setting mode you can choose between °C (Celsius) or °F (Fahrenheit) as temperature unit.
7.1.4 Rainfall amount unit setting
• In the setting mode you can choose between mm (millimeter) or in (inch) as rainfall amount unit.
8. Rain gauge functions
8.1 Rainfall amount indication
• The rainfall amount is shown on a corresponding cylinder graph.
• Press the RAIN button in normal mode to change the display between the rainfall amount indications:
• CURRENT rainfall amount from the start of a rain event. Automatic reset after 30 minutes of no rainfall.
• Rainfall amount of the last hour (1HR)
• Rainfall amount of the last 24 hours (24HR)
• Rainfall amount of the last 7 days (7DAYS)
• Rainfall amount of the last month (MONTH)
• Indication of TOTAL rainfall amount since setting up or the last reset.
• NOTE: Hold CLEAR/UP button for 3 seconds in the respective rainfall amount indication to clear the recorded
readings. Every rainfall amount indication can be reset individually.
19