Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
sample cut on a piece of scrap lumber. This will show
exactly how the cut will look as well as enable you to
check dimensions. (Fig. 7)
NOTE:
• When using the straight guide, be sure to install it on
the right side in the feed direction. This will help to keep
it flush with the side of the workpiece.
Straight guide (Fig. 8)
The straight guide is effectively used for straight cuts
when chamfering or grooving. (Fig. 9)
To install the straight guide, insert the guide bars into the
holes in the tool base. Adjust the distance between the bit
and the straight guide. At the desired distance, tighten the
wing bolts to secure the straight guide in place.
When cutting, move the tool with the straight guide flush
with the side of the workpiece. (Fig. 10)
If the distance (A) between the side of the workpiece and
the cutting position is too wide for the straight guide, or if
the side of the workpiece is not straight, the straight guide
cannot be used. In this case, firmly clamp a straight board
to the workpiece and use it as a guide against the router
base. Feed the tool in the direction of the arrow.
Dust nozzle set (For European countries
only) (Fig. 11)
Use the dust nozzle for dust extraction. Install the dust
nozzle on the tool base using the thumb screw so that
protrusion on the dust nozzle fit to the notch in the tool
base. (Fig. 12)
Then connect a vacuum cleaner to the dust nozzle.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Straight & groove forming bits
• Edge forming bits
• Laminate trimming bits
8
Router bits
Straight bit (Fig. 13)
D
A
6
20
1/4"
8
8
6
8
1/4"
6
6
1/4"
"U"Grooving bit (Fig. 14)
D
A
6
6
"V"Grooving bit (Fig. 15)
D
A
1/4"
20
Drill point flush trimming bit (Fig. 16)
D
A
8
8
6
6
Drill point double flush trimming bit (Fig. 17)
D
A
L1
8
8
80
6
6
70
Corner rounding bit (Fig. 18)
D
A1
A2
6
25
9
6
20
8
Chamfering bit (Fig. 19)
D
A
L1
6
23
46
6
20
50
6
20
49
Cove beading bit (Fig. 20)
D
A
6
20
6
25
L1
L2
50
15
60
25
50
18
50
18
L1
L2
R
50
18
L1
L2
50
15
90°
L1
L2
L3
60
20
35
60
18
28
L2
L3
55
20
40
12
L1
L2
L3
48
13
5
45
10
4
L2
L3
11
6
30°
13
5
45°
14
2
60°
L1
L2
R
43
8
48
13
mm
mm
3
mm
mm
mm
L4
25
14
mm
R
8
4
mm
mm
4
8
Publicidad
Tabla de contenido
