Before Starting The Equipment - Robust RB-CD 18 Li Manual De Instrucciones

Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Be sure to read the following information before
you use your cordless screwdriver for the fi rst
time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 3 to 5 hours.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate.
3. Plug the battery charger (6) into the power
socket and connect the charging cable (a) to
the battery (5). The three LEDs on the battery
capacity indicator (10) indicate that the batte-
ry is being charged.
- Battery empty: All three LEDs fl ash alterna-
Anl_RB_CD_18_Li_SPK7.indb 20 Anl_RB_CD_18_Li_SPK7.indb 20
GB
tely
- 1/3 charged: The LED on the left lights up
and the LEDs in the middle and on the right
fl ash alternately
- 2/3 charged: The LEDs on the left and in
the middle light up and the LED on the right
fl ashes
4. When charging is fi nished after approx. 3-5
hours, all three LEDs light up for approx. 10
minutes. Remove the charger from the batte-
ry.
5. If all three LEDs fl ash at the same time, the
battery temperature is either too low or too
high. Remove the charger from the battery,
keep the battery at room temperature for a
day and try again.
6. If the fault is still indicated, the battery is
defective. Do not use or charge a defective
battery. Remove the charger from the battery.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that the LI battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
6.2 Torque setting (Fig. 4 / Item 1)
Important! The tool must be at a standstill
when you set the torque with the setting ring.
The cordless screwdriver is fi tted with a mechani-
cal torque selector.
The torque for a specifi c size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
on the type and hardness of material in ques-
tion
•
on the type and length screws used
•
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
- 20 -
07.11.2016 13:08:17 07.11.2016 13:08:17