Publicidad
EN
Deploy the antennas to the highest point in order to get an effective range and best result.
Do not put the microphone directaly towards the speaker of the main receiver in near distance. or it will occur
screaming feedback.
OPERATION WITH USB/SD PLAYER
The MP3 player of the wireless PA amplifier provides 2 types of interfaces: USB 2.0 port and SD/MMC car slot.
Both of them can play MP3 format sound files.
INSERTING USB DISK OR SD CARD ALONE:
1. Insert USB disk into USB port and turn on the USB/SD volume switch, then press the
playing. The USB indicator turns bright. To pause playing, please press the
playing press the STOP button.
2. Insert SD card into SD card slot, and turn on the USB/SD volume switch, then press the
playing, the SD card indicator turns bright. To pause playing, please press the STOP button.
INSERTING USB DISK AND SD CARD SIMULTANEOUSLY:
1. Insert USB disk and SD card into USB port and SD card slot respectively. Turn on the USB/SD volume switch.
II
2. Press the
button to start playing. The play/pause LED turns bright. If you insert USB disk first and SD
card after, the amplifier will play in priority the songs in USB disk.
If you need to change to play the songs in the SD card, press the USB/SD switch button, then press the
button to play. To pause playing, press the
Adjust USB/SD volume knob to a proper volume. Adjusting tone knobs can make the sound quality more pleasing.
I
Press
button to play the next song, and press twice the
Modes of Loop-play
1. Push the MODE once, the MODE LED flashes slowly, MP3 player will cycle play the music which is playing.
2. Push the MODE twice, the MODE LED flashes quickly, MP3 player will cycle play the folder which is playing.
3. Push the MODE triple, the MODE LED lights all time, the MP3 player will cycle play all the files in the USB and
SD card.
4. Push the MODE fourth, the MODE LED dims, delete the cycle play function, MP3 player will stop automatically
after it read and play all the files in the USB or SD card.
NOTICE
1. The SD card slot can only read the SD card whose capacity is equal to or bigger than 64 MB.
2. To draw out the USB disk or SD card safely ater playing, you should first press the stop button,
turn off the USB/SD volume switch, and then draw out the USB disk or SD card.
OPERATION WITH WIRED MICROPHONE
Plug the microphone to the wired mic input jack. Turn on the MIC switch, then you can hear your voice immediately.
Total 4 wired microphone can be used at the same time.
OPERATION WITH BASS & TREBLE CONTROLS
Move the Bass or Treble knob for minimum to maximum to adjust their level to your desire.
OPERATION WITH DIGITAL ECHO
Move ECHO knob for minimum to maximum to adjust their level to your desire. If you hear screaming sound,
adjust the ECHO knob in less volume.
II
button to start
II
button again. To stop
II
button to start
II
button once again. To stop playing press the STOP button.
I
button to play the last one.
Page 6
User Manual
CARACTERISTICAS
Componentes electrónicos SMD y tecnología SMT usado en el diseño este amplificador.
Sistema VHF dual.
4 grupos (8 frecuencias) disponibles a elegir.
El sistema opera con 3 tipos de alimentación: Aliment. AC, Batería recargable incorporada de 7 AH y alimentador
externo DC 12 V (no incluido).
4 micrófonos con cable/2 inalámbricos pueden ser usados al mismo tiempo.
Controles Bass y Treble.
Echo digital.
3 entradas AUX para el conexionado de dispositivos MD/CD/MP3.
Salida AUX.
Puerto USB/SD
Indicador LED de alimentación.
Indicadores LED que marca el proceso de recarga de la batería incorporada de 12V y el cargador de 8.4 V.
Circuito de protección de baja tensión para evitar que la batería recargable se pueda dañar en caso de manejo
incorrecto.
Inserción en la parte inferior para su colocación sobre un trípode.
DESCRIPCION DEL SISTEMA
II
WAP 650
Botón modo Loop
Botón de selección SD/USB
Botón Stop
LED modo Loop
Puerto SD / MMC
LED Play/Pause
Slot USB
Botón Play/pause
Botón Backward
Botón Fordward
Manual de Instrucciones
Página 11
ES
WAP 650
Publicidad
