Steinberg SBS-KW-3000 Manual De Usuario página 17

DISPLAY BRIGHTNESS
Press or to enter Display Brightness. br||? shows.
Press or and to change brightness value.
Display Brightness can be set to:1(dim), 2(normal), 3(bright).
Dim LED brightness saves battery power dramatically.
IDLE MODE TIMING
Press or to enter Idle Mode Timing. idl?? shows.
Press or and to change timing value.
Idle Mode Timing can be set to: 0(disabled), 5(5sec), 10(10sec), 15(15sec),
30(30sec), 60 (60sec). It is 30sec by default.
To maximize battery life, the scale automatically enters Idle Mode, when there's
no action or the load is stable. In Idle Mode, the scale works in low-power con-
sumption status. Any key pressing or motion in load wakes up the scale from Idle
Mode.
Press or to exit User Setup.
SCALE CONFIGURATION
ATTENTION: The parameters in Scale Configuration are closely related
EN
to the scale's metrology performance. It is NOT recommended to change
any parameters unless you absolutely need to. In case you´re not sure,
please contact the customer service to check if it is necessary to modify
these parameters.
SCALE CONFIGURATION
ENTERING THE MENU
Press twice, enter Password mode.
The Scale displays Input Scale Configuration password P0258 . To do
so, press or , then
, to move the digit.
Press or , to confirm the input and enter the Scale Configuration.
Scale displays .
DISPLAY RESOLUTION
The display resolution can be set to: The display resolution can be set to: 0.001,
0.002, 0.005, 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, or 50.
Press or to enter the Display Resolution. E--- shows.
, to modify the digital. Press or
29
Press or
AUTO-ZERO RANGE
The Auto-Zero range can be set to: 0% (disabled), 2 (±2%FS), 3 (± 3%FS), 4
(±4%FS), 10 (±10%FS), 20 (±20%FS), 50 (±50%FS), 100 (±100%FS). It is set
to ±20%FS by default.
Press or
Press or
MANUAL ZERO RANGE
The manual zero range can be set to: 0% (disabled), 2 (±2%FS), 3 (±3%FS), 4
(±4%FS), 10 (±10%FS), 20 (±20%FS), 50 (±50%FS), 100 (±100%FS).
Press or
The scale displays the Manual-Zero range,
only allowed when the weight is within the Manual-Zero range.
Press or
ZERO TRACKING RANGE
The Zero-Tracking range can be set to: 0 (disabled), 0.5 (±0.5e), 1.0 (±1.0e),
1.5 (±1.5e), 2.0 (±2.0e), 2.5 (±2.5e), 3.0 (±3.0e), 3.5 (±3.5e), 4.0 (±4.0e), 4.5
(±4.5e), 5.0 (± 5.0e). Enabling the Zero-Tracking will enhance the scale tempe-
rature and drift the performance!
Press or
The scale displays the Zero-Tracking range,
Press or
ZERO RANGE
Zero Range defines the range that scale must fall into before activating the accu-
mulation operation. When the load is removed from the scale, the weight left must
, and
be lighter than the value set.
Press or
Press or
Press or
, to set the decimal point. Zero Range can be set from 0e to 3000e. It is set to
„5e" by deafult.
ZERO-SAVING
When Zero-saving is enabled, Auto Zero is disabled automatically. Scale calcu-
lates weight based on the last Zeroing action. It is disabled by default.
Press or , to enter Zero Saving.
Press or
and to change the resolution value.
to enter the Auto-Zero range setting.The scale displays
and to change the value.
to enter the Manual-Zero range setting.
and to change the value.
to enter the Zero tracking range setting.
and to change the value.
to enter the Zero range setting.
and to change the value.
and , to move the digit. Input the Zero Range value. Press
shows.
and , to change the status to „on" (enabled) or „off" (disabled).
30
indicating 4% F.S.. Zero is
EN
indicating 0.5e.
shows