Overhead Rigging - JB Systems Light LEDBALL INDOOR Manual De Instrucciones

ENGLISH
An example to make things clear:
We want to set the DMX-addresses of 16 units, the DMX start address of the first projector must
be 202:
 Connect all projectors to the DMX-controller as described above and make sure all are switched
on.
 Set all DMX-channels on the controller to zero (000)
 Now set DMX-channel 202 to maximum (255)
 Press the "Auto DMX address" button (6) on the first projector in the chain for about 5seconds.
 Done!  The first projector in the chain will receive DMX-start address 202 and it will
automatically calculate and program the DMX addresses of all the other units in the DMX-chain!
nd
This means that the 2 projector automatically receives address 206, the 3
th
..., until the 16 projector who automatically receives start address 262.
You just programmed 16 projectors, this took you about 10seconds!!!
Remark: you can mix the units with other DMX-effects that don't have the automatic DMX-
addressing option. In that case you still have to set the DMX-addresses of these DMX-effects
manually!

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
 3 different fixing methods are possible:
 Fixed to ceiling or truss (1m chain included)
 Wall fixing (optional wall adapter available)
 Pole mount (optional adapter for poles up to D=60mm available)
JB SYSTEMS
®
OPERATION MANUAL
rd
has address 210,
5/36 LED BALL INDOOR
ENGLISH
OPERATING INSTRUCTIONS
A. Standalone 1unit:
 Just connect the unit to the mains and put on some music. The unit will start working automatically to
the rhythm of the music.
Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
 Connect 2 to maximum 16 units together. Refer to the chapter "electrical installation" to learn how to
do this (don't forget to address all units properly!)
 Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music and show the internal chase programs.
Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
IMPORTANT REMARK:
When you use this LED PROJECTOR with a CA-8 controller and you select MANUAL mode
(mode LED = ON), the projector reminds the last setting used with controller, even after
disconnecting the controller and/or the mains voltage. If you don't want this, make sure to
select another working mode (mode LED must blink or off) before you unplug the
BUTTON
STANDBY
Strobe 9 Color select
White  Red 
1.Synchronous strobe
Blue  Purple 
in white color
FUNCTION
Orange  Green 
2.The same color
Yellow  Magenta
chase
 Cyan
3.Different color
strobe
Sound 1 Manual
MODE
(LED OFF) (LED ON)
D. Controlled by universal DMX-controller:
 Connect all units together. Refer to
the chapter "Electrical installation for
two or more units in DMX-mode" to
learn how to do this (don't forget to
address all units properly!)
 Connect all units to the mains and
turn on the DMX controller.
Since each unit has its own DMX-
address, you can control them
individually. Remember that each unit
uses 4 DMX-channels as shown in the
DMX chart.
JB SYSTEMS
®
OPERATION MANUAL
controller.
ACTIONS
To blackout all the fixtures
Color Chase Color Fade
1. The same color 1. Fast speed
2. Different color 2. Middle speed
3. One light chase 3. Slow speed
4. Two lights chase
5. Four lights chase
Sound 2 Auto
(LED slow blinking) (LED fast blinking)
6/36 LED BALL INDOOR