Charging; Turning The Power On/Off; Connecting A Bluetooth ® Device - Panasonic RP-BTD5 Instrucciones De Funcionamiento

Charging

The rechargeable battery (installed in the unit) is not charged initially. Charge
the battery before using the unit.
1
Connect this unit to a computer
using the USB charging cord
• Within approximately 3 seconds after
the connection is established, the LED
on the right speaker will light in red.
• The LED lights in red when charging
is in progress. When charging is
completed, the LED will go out.
• Charging will take approximately
3.5 hours from empty state to fully
charged.
■
Note
• The Bluetooth feature cannot be used when this unit is connected to a computer
®
using the USB charging cord.
• Charge in a room temperature between 10 °C and 35 °C (50 ºF and 95 ºF).
Outside of this range of temperatures, charging may stop.
• The power cannot be turned on while charging.
• Do not use any other USB charging cords except the supplied one.
Caution: Use only the supplied USB charging cord when connecting to a
computer.

Turning the power on/off

1
Press and hold the power
approximately 3 seconds
• A beep will sound and the LED on the right speaker
will blink.
To turn the power off
• Press and hold the power button for approximately 3 seconds. A beep will
sound and the power will be turned off.
■
Note
• When the unit is not operated for approximately 5 minutes, the power will
automatically turn off. (See "Auto power off" (→ P. 5))
Right
Computer
USB charging cord (supplied)
button for
LED
Power button
Connecting a Bluetooth
To establish a wireless connection, register the unit with Bluetooth
devices.
Preparation on the Bluetooth
• Turn on the power, and enable the Bluetooth
LED • Place the device within 1 m (3.3 feet) from the unit.
• Check the device operation in its operation instructions, as required.
Power on for the first time
1
Turn on the unit
• The unit will start searching for
the Bluetooth ®
to, and the LED on the right
speaker will blink in blue and red
alternately. (Only one operation
after purchase)
2
When the unit ("RP-BTD5")
is detected by the Bluetooth
device, select it
• If prompted for a passkey, input
"0000 (four zeros)".
• If the Bluetooth
screen appears, select the
"A2DP" profile. If "A2DP" is not
supported or if you want to just
use phone calls, select the "HSP"
or "HFP" profile. (For details on
profiles, see "Listening to music"
(→ P. 4) and "Making a phone
call" (→ P. 5))
3
Check the connection with
the Bluetooth ®
unit
• First the LED on the right
speaker lights in blue and
repeats on and off. When the
connection is established,
blinking pattern will change.
® device
® feature.
Connection after the second
time
<Connect the same Bluetooth
When the unit is turned on, it will
device to connect
search for the previously setup
Bluetooth device and automatically
®
start connecting to it. First the LED
on the right speaker lights in blue
and repeats on and off. When the
connection is established, blinking
®
pattern will change.
<Connect a different Bluetooth
device>
profile selection Disable the Bluetooth
®
the previously connected device.
Check that the unit is turned off. Press
and hold the pairing
approximately 5 seconds. A beep will
sound. The unit will start searching for
other Bluetooth
the right speaker will blink in blue and
red alternately.
Continue steps 2 and 3.
device on the
■
Note
• If connection to a device is not
established within approximately
5 minutes, the unit will be turned off.
Start from step 1 again.
• 2 or more Bluetooth
be connected to the unit at the same
time.
• You can pair up to 8 devices with
this unit. If a 9th device is paired, the
device with the oldest connection will
be replaced. To use it, pair it again.
device
®
compatible
®
® device>
®
feature on
®
button for
® device. The LED on
® devices cannot
3
3