Tabla de contenido
Publicidad
Adjusting the wheel assembly (Fig. 5)
For edging purposes, the wheel assembly can be ad-
justed to 5 positions. Push the button (A) and turn the
grass shears into the desired position. Make sure that
the button locks into place again after turning.
Switching the tool on/off
Push the switch-on lock A (Fig. 5) to the left or right as
far as it will go and push the switch B. After the tool has
been switched on, you do not have to hold the switch-on
lock A any longer.
To switch off just let go of the switch B.
To switch the tool on/off with the telescopic handle
mounted only the switch integrated in the handle is used.
Attention! The blades will coast for a certain time
after switch-off!
Refitting the tool / Changing the shear systems
Do not switch on the tool when performing the
following steps to change the shear system!
Danger of injury!
Put the included blade guard into the blade(s) and use
protective gloves to protect yourself from injury.
Lift off the locking bracket (1) and slide the gear cover
back in the direction of the arrow (2). Remove the gear
cover. The shear blade can now be removed (Fig. 8).
Remove any dirt from the gear area (if necessary).
Please slightly grease the drive area using commercial
universal grease as described in the Maintenance sec-
tion before putting the replacement shears in place (Fig.
9 + 10).
Turn the gear wheel to move the eccentric wheel to
either the front or rear position (Fig. 9). Move the move-
able part of the shear blade to the centre position to
locate the opening of the eccentric wheel exactly over
the hole in the shear blade (Fig. 9). [ Grass/shrub shears
(Fig. 10): Move the moveable part of the blade forward
or backward until the eccentric wheel (A) fits into the
eccentric opening (B).] Put the shear blade in place. If
the blade cannot be placed flush into the housing, adjust
the positions of the eccentric wheel and moveable shear
blade again.
Then put the gear cover into the guiding grooves and
slide it forward until the locking bracket locks into place
(Fig. 11).
The device is now ready for operation.
Hints for your work with the tool
The shrub trimmer cuts ornamental shrubs and light
undergrowth or bushes. The device is also well-suited
for ornamental cuts as, for example, for the care of
graves. As the device is operated with one hand please
be careful not to move the other hand near the running
cutting tools.
GB | Operating Instruction
The grass shears allow for clean cuts of lawn edges or
hardly accessible lawn areas.
For convenient working in an upright position, the in-
cluded telescopic handle may be assembled to the tool.
Maintenance
Clean the blade from any crushed plants and dirt. The
blades should be detached at least once a season for
the removal of debris. Lubricate the C pinion and the
D back of the blade with a light oil. Do not lubricate the
motor and other parts. Should the blade become dull
after a long period of use, a spare part can be ordered.
Warning! The leading edges of the blades must be oiled
to ensure proper lubrication. If the leading edges are not
oiled, blade durability may be adversely affected.
If the cutting tools have become dull after long use
please replace them with original spare parts.
Clean the device using only a brush or cloth. Do never
wash down the device with water and do never dip the
device into water.
Apply protective spray to the blades after each use.
Replace blunt blades.
Always put on the blade guard after use.
Examine the tool for obvious defects and have it repaired
in an authorised service shop if required.
Storage
Always store the tool in a dry, clean place outside the
reach of children. Make sure that the place of storage
is frost-free.
Waste disposal and environmental protection
Batteries are not to be put into the rubbish. As a con-
sumer you are legally obliged to return used batteries
and accumulators. At the end of the duration of your ap-
paratus, the batteries or accumulators have to be taken
from the apparatus, disposing of them separately. You
have the possibility of delivering your old batteries and
accumulators to the local collecting points of your mu-
nicipality or to your dealer or to the distribution centers.
If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
of the device together with your domestic refuse, but
dispose of it in an environmentally friendly manner.
Please dispose of the device itself at an according col-
lecting/recycling point. By doing so, plastic and metal
parts can be separated and recycled. Information con-
cerning the disposal of materials and devices are avail-
able from your local administration.
4
Please observe the following directions for the
disposal of your accumulator/battery.
Publicidad
Tabla de contenido
