How To Replace The Turntable Stylus (Needle) - Muse MT-102 JS Manual De Instrucciones

Certain types of records may have an auto-stop area outside the preset limit, so the turntable may stop before the last
track finishes. If this occurs, set the AUTO-STOP switch to the "OFF" position. This allows the record to play to the end, but
please note that it will not stop automatically. You must manually raise the tone arm and place it back in the rest and then
turn off the power to stop the turntable from spinning.
IMPORTANT:
Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm
Clamp could result in damage to the Tone Arm or Stylus.
USING THE AUX IN MODE
1. Connect one end of the cable (not supplied) to the auxiliary input connector of the unit(cable not supplied).
2. When the unit is on, Repeatedly press MODE button to select AUX IN mode until function indicator light becomes BLUE.
Normally use your external audio appliance, the sound automatically goes through the speakers of your device.
3. Adjust the volume to the desired level.
4. Disconnect the external appliance from the auxiliary input to stop playback.
LISTEN TO THE DEVICE USB
1. Connect a USB device containing MP3 files or MP3 player to the USB port.
2. When the unit is on, Repeatedly press MODE button to select the USB mode until function indicator light becomes
PURPLE.
3. Press PLAY/REC to start playback, indicator light turns red with flashing.
4. Adjust the volume to the desired level.
5. Press NEXT to skip forward to the next track or repeatedly to several tracks. Press PREV return to the beginning of the
track, or press repeatedly to skip backwards several tracks.
6. Press PLAY/REC to stop the USB playback.
Removing the USB device
Please be sure to stop playback and turn the unit OFF before removing the USB device to avoid damage the USB and
system.
ENCODING FROM PHONO, AUX IN TO USB
1. Connect the USB device to the USB port(Make sure the USB device have enough space to save the encoding).
2. Select one of your favorite mode(PHONO or AUX IN) and start your mode playback.
3. Press PLAY/REC for two seconds until the function indicator light flashing, then recording starts.
4. Press PLAY/REC to stop encoding.
5. To listen the recording, repeatedly press MODE to select the USB mode until function indicator becomes PURPLE.
6. Press PLAY/REC to listen, indicator light turns red with flashing.
7. Press STOP to stop playback.
Using the RCA line out jack
Connect one end of audio cable (cable not included) to the LINE OUT jack on the rear of unit and other end of cable connect
to the RCA IN jack or AUX in jack of your other audio drive equipment.
1. Turn on your audio drive equipment.
2. Select one of your favorite mode (PHONO, USB, AUX IN) and start your mode playback.

HOW TO REPLACE THE TURNTABLE STYLUS (NEEDLE)

Removing the Stylus(needle) from the Cartridge
1. Raise the Tone Arm.
To remove the old stylus needle, Place a screwdriver
at the tip of the stylus and push downward as shown in
direction "A".
2. Remove the stylus by pulling the stylus forward and
pushing downward.
HXT-3705 IB MUSE 001 REV2.indd 5
Installing the Stylus
1. Hold the tip of the stylus and insert the stylus by pressing
as shown in direction "B".
2. Push the stylus upward as in direction "C" until the
stylus locks into the tip position.
EN - 3
TIPS FOR BETTER TURNTABLE PERFORMANCE
1. When opening or closing the turntable cover, handle it gently, gripping it either at the centre or at each side.
2. Do not touch the needle tip with your fingers; avoid bumping the needle against the turntable platter or record edge.
3. Frequently clean the needle tip-use a soft brush in a "back-to-front' motion only.
4. If you must use a needle cleaning fluid, use very sparingly.
5. Gently wipe the dust cover and turntable housing with a soft cloth. Use only a small amount of mild detergent to clean
the turntable and dust cover.
6. Never apply harsh chemicals or solvents to any part of the turntable system.
SPECIFICATIONS
GENERAL
Power: 100-240V AC, 50/60Hz 0.15A
Power Output: DC 5V 1A
Max. Output Power: 2 X 1.2W
RECHARGEABLE BATTERY
Battery Type: 3.7V 2000mAh Lithium Polymer Battery
Charging Voltage: 5V DC
Operating Time: Approx. 8 hours at 50% volume after fully charged
Charging Time: Approx. 8-10 hours
MORE INFORMATION
CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). There are no user
serviceable parts inside the unit. Refer all servicing to qualify personnel.
The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of " dangerous
voltage" inside the unit.
The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying
the product.
WARNING!
• The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths,
curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• The use of apparatus in moderate climates.
• The apparatus should not be exposed to dripping or splashing.
• Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation.
• Do not place objects filled with liquids, such as vases, on the apparatus.
• The marking plate is located on the back of unit.
• Under the influence of electrical fast transient or/and electrostatic phenomenon, the product may malfunction and require
user to power reset.
If at any time in the future you should need to dispose of this product please note that Waste electrical products
should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.(Waste Electrical and Electronic Equipment Directive)
NEW ONE S.A.S
10, Rue de la Mission, 25480 Ecole Valentin, France
EN - 4
2016/8/22 17:42:02