SOLAC CVG9511 Instrucciones De Uso página 10

pump will automatically switch off after 25" to
30" to protect the micro-pump
If the appliance were to run out of water com-
•
pletely with the steam selector activated,
you would hear a strange noise from the mi-
cro-pump. Switch off the steam selector to pre-
vent any damage to the system.
Switch off the appliance and fill the water tank.
•
When switching it on again, this noise will di-
sappear.
USE:
Unroll the cable completely before plugging it
•
in.
Connect the appliance to the mains.
•
- Once plugged in the appliance begins to heat
up to its default ECO setting. Automatic tempe-
rature for all fabrics and optimised steam flow for
efficient, safe ironing.
Do not use temperatures higher than those in-
•
dicated on the garments to be treated.
ECO Temperature for synthetic fibres (Polyes-
•
ter, Nylon...). Setting ●
ECO Temperature for silk, wool.
•
Setting ●●
•
TURBO Temperature for cotton. (Minimum
•
temperature for ironing with steam)
Setting ●●●
•
TURBO Temperature for linen. Max setting.
•
If garment has various kinds of fibres, select
•
the temperature for the fibre that requires the
lowest temperature. (For example, select the
temperature for polyester for an article made
out of 60% polyester and 40% cotton).
Wait until the indicator (G) is lit steady green,
•
this means that the appliance has reached
temperature, while it is heating or cooling the
indicator will flash red.
- While using the appliance the indicator light
•
(G) remains a steady green
PRESENCE SENSOR (D)
The CVG is equipped with a presence sensor
•
(D) that instantly shuts off the steam outlet if
the handle is not being held. This leads to
energy savings and increased autonomy of the
water tank (lower water consumption).
Steam flow is automatically re-established by
•
holding the handle on the CVG
Removing your hand from the handle does not
•
switch off the selected steam function, it only
interrupts the steam flow temporarily until it de-
tects that the handle is being gripped again.
The screen continues to display the icon for
the selected steam function.
DRY IRONING:
The appliance has a steam control button
•
(C) which, when set to off, allows dry ironing
(without steam) or with steam if it is switched
on, a light indicates its status, on/enabled off/
disabled.
STEAM IRONING:
It is possible to iron with steam as long as the
•
tank has water and at any setting.
STEAM BLAST:
This function proportions extra steam for elimi-
•
nating wrinkles.
Press the steam blast button (B), always in the
•
TURBO position, and wait a few seconds for
the steam to penetrate the fibres of the gar-
ment before pressing the button again. For op-
timum steam quality, do not apply more than
two successive blasts at a time. If the steam
indicator flashes DO NOT USE THE SUPERS-
TEAM FUNCTION
The steam blast button has to be pressed re-
•
peatedly to release the first shot.
VERTICAL STEAMING:
It is possible to iron hanging curtains, items of
•
clothing on hangers, etc. To do so, follow the
instructions:
Iron from top to bottom while pressing the
•
steam control (B), follow the instructions given
in the Steam Blast section.
Important: for cotton and linen, it is recommen-
•
ded to have the soleplate in contact with the
material. For other more delicate fabrics, it is
recommended to keep the soleplate a few cen-
timetres away from the fabric.
STAND-BY FUNCTION:
In order to save energy, the appliance passes
•
to stand-by after 3 minutes if the user does not
use it.
To resume ironing just touch any button or the
•
handle of the iron.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
Unplug the appliance from the mains.
•
Drain the water out of the appliance.
•
Clean the appliance.
•
CLEANING
Disconnect the appliance from the mains and
•
EN