Front Panel; Before Use - JB Systems Control 5.2 Manual De Instrucciones

ENGLISH
OPERATION MANUAL
FEATURES
2 Independent Zones, each with balanced XLR-output (+unbalanced on cinch)
Each zone has 3band tone controls, balance, volume and mono/stereo switch
11 inputs on 5 Channels (5 balanced mic + 4line + 2phono)
1Microphone with 3band tone control and zone assignable adjustable talkover.
Every Channel can be assigned to zone A, zone B or both.
Every Channel has individual peak and signal present leds.
Gain levels and 45mm faders on all channels
PFL with rotary selector, cue level adjustment and 6.3mm headphones jack.
2 independent record outputs without Channel1 microphone and free from
talkover muting.

BEFORE USE

Check the contents:
Check that the carton contains the following items:
CONTROL5.2 Mixer unit
Operating instructions
Mains cable
Some important instructions:
Choose the place where you put your installation very carefully. Avoid presence of
heat sources. Avoid places with vibrations or places that are dusty and humid.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
In order to prevent electric shock, do not open the enclosure. If a problem occurs,
contact your dealer.
Do not place metal objects or spill liquid inside the mixer. Electric shock or
malfunction may result.
CONNECTIONS
Except for microphones, headphone and zone outputs, all connections are cinch.
Use good quality cinch-cinch cables to prevent bad audio quality. (example: JB
Systems code: 2-0370)
For more information on connections, please refer to the next chapter.
Be sure to turn off the mixer before you make changes to the different connections.
In this manual we talk about "line inputs". This is a global name for inputs with a level
between 750mV and 2V. This includes tuners, videos, CD-players, etc.
JB SYSTEMS
OPERATION MANUAL
1/24 CONTROL5.2 MIXER
ENGLISH

FRONT PANEL

1. DJ MICRO input: The DJ micro can be connected to the XLR/Jack input on the
front plate or to the stereo jack on rear panel. This input is balanced but accepts
any kind of microphone equipped with an XLR or jack connector.
2. TALKOVER level: When you switch the talkover(3) on, you can adjust the
amount of muting on input channels 2 to 5. The more you turn to the right, the
more these channels are muted while talking through the DJ Micro(1).
3. TALKOVER switch: Use this switch to automatically mute the input channels 2 to
5 while you are talking through the DJ microphone. Use the zone selectors(4) to
choose on which output the talkover should work.
Attention: the talkover will only work on the zone you selected for the DJ Micro. The other zone
won't be affected.
4. ZONE switch: for every input channel you can choose to which zone (master) it
should be routed. This means that you can use this mixer to serve two different
rooms with completely different music!
Example:
You want channels 2&3 to be routed to Master A (room1). Channels 4&5 must
be routed to Master B (room2). But you want to be able to make
announcements in both rooms. This is what you should do:
• Select "zone A" on channels 2&3
• Select "zone B" on channels 4&5
• Select "zone A" and "zone B" on DJ Micro input.
Now you can do announcements in both rooms, while the music you play in
both rooms is completely different.
5. INPUT SELECTOR switch: On channels 2 and 3 you can choose between line
or balanced micro inputs.
6. INPUT SELECTOR switch: On channels 4 and 5 you can choose between line
or balanced micro inputs but you can also connect a turntable. (line/phono switch
on the back)
7. MONO/STEREO switch: used to switch Master A in mono or stereo mode.
8. BALANCE: used to adjust the balance between left and right output on Master A.
9. VU-meters: Used to monitor the level of the audio signals selected with the CUE
selector(13). With the channel faders you can change the input level of each
connected audio source. Make sure the levels do not exceed 0dB (or 100%). The
JB SYSTEMS
OPERATION MANUAL
2/24 CONTROL5.2 MIXER