Festool TS 75 EBQ Instrucciones De Servicio página 9

Technical data
Power
Speed (idling)
Inclination
Cutting depth at 0°
Cutting depth at 45°
Saw blade dimensions
Weight
Degree of protection
The specifi ed illustrations can be found at the
beginning of the operating instructions.
1 Use for intended purpose
These machines are intended to be used for
sawing wood, wood-like materials, plaster and
cement-bonded fi bre materials, and plastics.
With the special saw blades for aluminium of-
fered by Festool, these machines can also be
used for sawing aluminium.
Only saw blades with the following specifi cations
must be used: saw blade diameter of 210 mm;
cutting width of 2.4 mm to 2.6 mm; toolhol-
der diameter of 30 mm; blade core thickness
of max. 1.8 mm; suitable for speeds of up to
5000 rpm. Do not use any abrasive wheel.
The user is liable for damage and
injury resulting from incorrect usa-
ge!
2 Safety instructions
2.1 General safety rules
Before using the machine, read the
enclosed safety instructions and these
operating instructions carefully and
thoroughly.
Save all enclosed documents and pass the ma-
chine with all these documents only.
2.2 Tool-specifi c safety rules
DANGER
a) Keep hand away from cutting area and the
blade. Keep your second hand on auxiliary
handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the
blade.
b) Do not reach underneath the workpiece. The
guard cannot protect you from the blade
below the workpiece.
c) Adjust the cutting depth to the thickness
of the workpiece. Less than a full tooth of
the blade teeth should be visible below the
workpiece.
d) Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a
stable platform. It is important to support the
work properly to minimize body exposure,
blade binding, or loss of control.
e) Hold power tool by insulated gripping sur-
faces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a „live" wire will
also make exposed metal parts of the power
tool „live" and shock the operator.
TS 75 EBQ
f) When ripping always use a rip fence or
1600 W
1350 - 3550 rpm
0° - 47°
0 – 75 mm
g) Always use blades with correct size and shape
0 – 56 mm
210x2.4x30 mm
6.2 kg
/II
h) Never use damaged or incorrect blade was-
i) Wear suitable protection such as
Causes and operator prevention of kick-
back
- kickback is a sudden reaction to a pinched,
- when the blade is pinched or bound tightly
- if the blade becomes twisted or misaligned
Kickback is result of saw misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given
below.
a) Maintain a fi rm grip with both hands on the
b) When blade is binding, or when interrupting
c) When restarting a saw in the workpiece, cen-
d) Support large panels to minimise the risk of
9
straight edge guide. This improves the accu-
racy of cut and reduces the chance of blade
binding.
(diamond versus round) of arbour holes. Bla-
des that do not match the mounting hardware
of the saw will run eccentrically, causing loss
of control.
hers or bolt. The blade washers and bolt
where specially designed for your saw, for
optimum performance and safety of operati-
on.
ear protection, safety goggles,
a dust mask for work which
generates dust, and protective
gloves when working with raw
materials and when changing
tools.
bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the
workpiece toward the operator;
by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back
toward the operator;
in the cut, the teeth at the back edge of the
blade can dig into the top surface of the wood
causing the blade to climb out of the kerf and
jump back toward the operator.
saw and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the saw to jump back-wards,
but kickback forces can be controlled by the
operator, if proper precautions are taken.
a cut for any reason, release the trigger and
hold the saw motionless in the material until
the blade comes to a complete stop. Never
attempt to remove the saw from the work or
pull the saw backward while the blade is in
motion or kickback may occur. Investigate
and take corrective actions to eliminate the
cause of blade binding.
tre the saw blade in the kerf and check that
saw teeth are not engaged into the material.
If saw blade is binding, it may walk up or
kickback from the workpiece as the saw is
restarted.
blade pinching and kickback. Large panels
tend to sag under their own weight. Supports