Replacing The Intellibrite; Before Replacing The Intellibrite; Spa Light Fixture - Pentair Water LED IntelliBrite Guía De Instalación Y Del Usuario

4
2. Cut the cord at the Junction Box, leaving at least six (6) inches of cord to make connections.
3. Strip 6 inches of the outer cord jacket to expose the three insulated wires (be careful not to damage the insulation
on the three inner wires).
4. Connect all three (3) wires to the corresponding circuit wires in the Junction Box and secure the Junction Box cover
in place.
WARNING - Never operate this underwater light for more than ten (10) seconds unless it is totally submerged
in water. Without total submersion, the light assembly will get extremely hot, which may result in serious burns
or in breakage of the lens. This may result in serious injury to pool users, installers, or bystanders, or in damage
to property.
5. Install the IntelliBrite
WARNING - Use only the special pilot screw provided with this underwater light. This screw mounts and
electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided
could create an electrical hazard which could result in death or serious injury to pool users, installers or others
due to electrical shock.
6. Fill the spa until the light is completely submerged in the water. Before powering on the light, be sure the light is
completely submerged in the water. The light should never be powered on out of the water for more than 10 seconds.
Final check for proper light operation: Switch on the main switch or circuit breaker, as well as the switch which
operates the light itself. The light should illuminate what power is applied. If not recheck the installation steps starting
with Step 1 (page 3).

Replacing the IntelliBrite

The IntelliBrite
pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances.
Improper installation will create an electrical hazard which could result in death or serious injury to pool users,
installers or others due to electrical shock, and may also cause damage to property.
Always disconnect the power to the spa light at the circuit breaker before servicing the light. Failure to do so could
result in death or serious injury to serviceman, pool users or others due to electrical shock.

Before replacing the IntelliBrite

Verify that the pool and spa meets the requirements of the current National Electrical Code and all local codes and
ordinances. A licensed or certified electrician must install the electrical system to meet or exceed those requirements
before the underwater light is installed. Some of the requirements of the National Electrical Code which the pool and spa's
electrical system must meet are as follows:
• The lighting circuit has a Ground Fault Circuit Interrupter (GFCI) for line voltage models, and has an appropriately
rated circuit breaker.
• The Junction Box (or, for 12 volt models, the low voltage transformer) is located at least 8 inches above
ground level and at least 48 inches from the edge of the spa; see Figure 1.
• The light fixture and all metal items within 5 feet of the spa are properly electrically bonded.
• The wet niche is properly installed so that the top edge of the underwater light's lens is at least 18 inches below
the surface of the water in the spa; see Figure 1.
• The wet niche is properly electrically bonded and grounded via the No. 8 AWG ground connector located at the
rear of the niche; see Figure 1.
Note: The pool or spa electrical system can be verified with a Pool and Spa Electrical Qualification Test Kit. The test
kit is available from Pentair Water Pool and Spa, Inc. The electrical system inspection using this kit must be performed
by trained and certified personnel.
• To be certain that the spa's electrical system meets all applicable requirements, the electrician should also
consult the local building department.
• Use only Pentair Water Pool and Spa
® light assembly into the niche. Tighten the special bronze pilot screw to secure in place.
® Spa Light fixture in an existing spa
DANGER! Risk of Electrical Shock or Electrocution!
®
underwater LED spa light must be installed by a licensed or certified electrician or a qualified
®
®
wet niches to insure proper bonding and grounding connections.

Spa Light fixture