Important; Tool Use And Care; Specific Safety Rules For Routers - Surtek RR616A Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
Do not use tools if switch does not turn it on
or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in work pieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
E N G L I S H •
SERVICE
Tool service must be performed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.
SPECIFIC SAFETY RULES FOR
ROUTERS
CAUTION: Cutting bits coast after the rout-
er is switched off.
• Hold the tool by insulated gripping surfac-
es (handles) when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a "live"
wire will make the exposed metal parts of the
tool "live" and shock the operator.
• Maintain a firm grip on the router with both
hands to resist torque upon starting the router.
• Never attempt to use the router motor with-
out first installing it in an approved base. Fail-
ure to heed this warning could result in per-
sonal injury and damage to the motor.
• Do not hold the router by hand for use in
an upside-down or horizontal position. The
router motor can separate from the base if it
is not properly attached according to the in-
structions.
• Tighten the collet/nut securely to prevent the
cutting bit from slipping. If the collet/nut is not
securely tightened, the cutting bit may detach
during use, causing serious personal injury.
• Never tighten the collet/nut without a cut-
ting bit installed in the collet /nut.
• Use clamps or other practical ways to se-
cure and support the work piece to a stable
platform, and hold the work piece rigidly in
position. Holding the work piece by hand or
against your body is unstable and may lead to
loss of control.
• Never hold the piece being cut in your hands
or across your legs. It is important to support
and clamp the work piece properly In order to
minimize body exposure, bit binding, and loss
of control.
• Always keep the chip shield clean and in
place.
• Stay alert and clear the router cutting-bit
path of any obstructions before starting the
motor. Keep the cutting area clear of all for-
U se r ' s m a n ua l
17

Publicidad

Tabla de contenido
loading

Tabla de contenido