Polar Alignment; Polar Alignment (With Optional Wedge); Wedge Align - Celestron NexStar 6SE Manual De Uso

P o l a r A l i g n m e
P o l a r A l i g n m e
Even though the NexStar can precisely track a celestial object while in the Alt-Az
position, it is still necessary to align the polar axis of the telescope (the fork arm)
to the Earth's axis on rotation in order to attempt long exposure astro
photography. This is accomplished by using the built-in wedge attached to the
steel tripod. This allows the telescope's tracking motors to rotate the telescope
around the celestial pole, the same way as the stars. Without the equatorial
wedge, you would notice the stars in the eyepiece would slowly rotate around the
center of the field of view. Although this gradual rotation would go unnoticed
when viewing with an eyepiece, it would be very noticeable on film.
Polar alignment is the process by which the telescope's axis of rotation (called
the polar axis) is aligned (made parallel) with the Earth's axis of rotation. Once
aligned, a telescope with a clock drive will track the stars as they move across the
sky. The result is that objects observed through the telescope appear stationary
(i.e., they will not drift out of the field of view). If not using the clock drive, all
objects in the sky (day or night) will slowly drift out of the field. This motion is
caused by the Earth's rotation.
The polar axis is the axis around which the telescope rotates when moved in
right ascension. This axis points the same direction even when the telescope
moves in right ascension and declination.
Definition

Polar Alignment (with optional Wedge)

The simplest way to get a basic polar alignment with your NexStar is to angle the tilt plate on the equatorial wedge accessory so that the
fork arm (or polar axis) is pointed towards the star Polaris. For help in locating Polaris, refer to the Finding the North Celestial Pole section
below. To polar align your NexStar:
1. Position the telescope tripod so that tilt plate hinge is facing towards north.
2. Gently rotate the telescope tube so that it is pointing straight up in the sky.
3. Loosen the Latitude Adjustment Lock on the tripod.
4. Slowly tilt the telescope towards the north until the scale on the Latitude Adjustment Rod is equal to the latitude of your
observing location. For example, if using your telescope from Los Angeles, you would set the scale to 34 degrees.
Note: To view your current latitude, select View Time-Site menu feature after completing a successful alignment.
5. Once in position, securely tighten the latitude adjustment lock to hold the telescope in place.
You are now ready to complete an EQ North (South) Alignment to begin finding celestial objects and a Wedge Align for a more
accurate polar alignment.

Wedge Align

The NexStar has two equatorial wedge alignment modes (one for the northern hemisphere and one for the southern) that will help you
polar align your telescope when using an optional equatorial wedge. After performing either an EQ AutoAlign or Two-Star Alignment,
Wedge Align will slew the telescope to where Polaris should be. By adjusting the tripod's tilt plate to center Polaris in the eyepiece, the
fork arm (polar axis) will then be pointing towards the actual North Celestial Pole. Once Wedge Align is complete, you must re-align
your telescope using any of the EQ alignment methods. Follow these steps to Wedge Align your telescope in the Northern Hemisphere:
1. With the NexStar set up as described in the section above and roughly positioned towards Polaris, align the telescope using either
the EQ AutoAlign or Two-Star Alignment method.
2. Select Wedge Align from the Utilities menu and press Enter.
Based on your current alignment, NexStar will slew to where it thinks Polaris should be. Use the tripod's tilt plate adjustment to place
Polaris in the center of the eyepiece. Do not use the hand control's direction buttons to position Polaris. Once Polaris is centered in
the eyepiece, press ENTER; the polar axis should then be pointed towards the North Celestial Pole.
n t
n t
This is how the telescope is to be set up for polar
alignment. The tube should be parallel to the
fork arm which should be pointed to Polaris.
30
Figure 6-3