Cleaning And Maintenance; Peg-Pérego After-Sales Service - Peg-Perego sdraietta melodia Instrucciones De Uso

product must be subject to sorted waste
collection.
INSTRUCTIONS
1 OPENING: to open the baby rocker, rotate the frame
bars forwards until they click (fig_a) and release the
sun canopy from the handle (fig_b).
2 ASSEMBLING THE BABY ROCKER: to fit the handle,
move the backrest into the vertical position (see point
4). Slot the handle into the tubes (fig_a) and fasten it in
place with a screwdriver, ensuring that the crosshead
screw is on the outside of the handle (fig_b). Tighten
well and periodically check that it is fixed properly.
3 ADJUSTING THE HANDLE: the handle can be set in 3
different positions. Push the two levers (fig_a) in the
direction of the arrows and at the same time rotate the
handle into the required position (fig_b).
The transport position is number 1.
4 ADJUSTING THE BACKREST: The backrest can be set in
3 different positions. Rotate lever 1 outwards (leaving
it in the open position) (fig_a), rotate lever 2 outwards
and at the same time adjust the backrest (fig_b). Once
in the selected position, remember to close lever 1
again.
5 ADJUSTING THE REAR LEDGE: the rear ledge can be set
at two different heights. To raise it, pull the two levers
outwards from both sides and at the same time push
the tabs upwards (fig_a). Rear ledge raised (fig_b).
6 SAFETY BELT: thread the safety belt through the
crotch strap and engage the buckle until it clicks
(fig_a). To release the safety belt, press the two sides
of the buckle and simultaneously pull the waist strap
outwards (fig_b).
7 STAND: the base of the baby rocker can be rocking
(fig_a) or stable. To stop it from rocking, rotate the
stabilizer stand outwards (fig_b).
8 SUN CANOPY: the baby rocker has a sun canopy that
can be placed in different positions. It attaches to the
handle at any height.
9 PLAY BAR: attach the play bar (fig_a). It can be fitted to
the front of the frame (fig_b) or to the handle (fig_c),
depending on the position of the backrest.
10 The play bar can be detached on one side only, and
rotated externally. To make the cow moo, press its
hooves (fig_b).
batteries are NOT included.
11 SOUND MODULE:
sound module requires 2 "penlight" type AA 1.5V
batteries. Use a screwdriver to unscrew the battery
compartment cover (fig_a), insert the batteries. (fig_b),
and then screw the cover back on. The sound module
has 2 volume settings and 8 music options (fig_c).
A: To switch on the sound module and to adjust the
volume, move the button upwards.
B: 4 playful tunes.
C: 4 soothing tunes.
To change the music, push the relevant buttons.
12 MP3: The baby rocker can reproduce music from the
most powerful MP3 players. Disconnect the plug and
socket on the sound unit (fig_a) and connect the male
plug to your MP3 player.
13 BOOSTER CUSHION: the baby rocker comes with a
booster cushion for newborn infants which can be
removed when the child gets bigger. To remove the
booster, unthread the crotch strap.
14 CLOSING: to close the baby rocker (fig_a), put the
handle and the back rest in the lowest position, press
button A on both sides at the same time and pull
together as in the figure. Before moving the closed
baby rocker, put the elastic loop around the fastener
(fig_b). When closed, the baby rocker is extremely
compact and takes up very little space (fig_c).
15 REMOVING COVERS: to remove the cover of the baby
rocker, detach the Velcro (fig_a), slip off the sound
module cover by moving it towards the front (fig_b),
then disconnect the sound module connector by
detaching the two jacks (fig_c).
16 Slip the cover side loop off the frame tubes (fig_a),
unbutton the back of the backrest (fig_b) and slide the
cover upwards (fig_c). Important: when re-covering
the baby rocker remember to insert the loop onto the
tubular frame.

CLEANING AND MAINTENANCE

PRODUCT MAINTENANCE: protect from the weather:
water, rain, or snow; prolonged and continuous
exposure to bright sunlight may give rise to colour
changes of various different materials; store this
product in a dry place.
CLEANING THE CHASSIS: periodically clean all plastic
parts with a damp cloth. Do not use solvent or
similar cleaning products; keep all metal parts dry to
prevent rusting; keep moving parts clean (adjustment
mechanisms, locking mechanisms) and free of dust
and sand and, if necessary, lubricate with light
machine oil.
CLEANING FABRIC PARTS: brush fabric parts to remove
dust and wash by hand at a maximum temperature of
30°C; do not wring; do not use chlorine bleach, do not
iron; do not dry clean; do not apply solvent-based stain
removers and do not dry in a tumble dryer.
PEG-PÉREGO S.p.A.
Peg Pérego can make changes at any time to the
models described in this publication for technical or
commercial reasons.
Peg Pérego is at the disposal of its customers and
consumers to ensure that all their demands and
queries are fully satisfied. It is a key part of our policy
to ensure we are always aware of our customers'
views and requirements. We would therefore be very
The
grateful if, after using a Peg Pérego product, you
take the time to fill in our CUSTOMER SATISFACTION
QUESTIONNAIRE, making a note of any comments
or suggestions you might have. You can find the
questionnaire on the Peg Pérego website: www.
pegperego.com
PEG-PÉREGO AFTER-SALES SERVICE
If any parts of your Peg Pérego product should be
accidentally mislaid or damaged, use exclusively
genuine original Peg Pérego replacements. For any
repairs, replacements, product information, and orders
for genuine original replacement parts and accessories,
contact Peg Pérego After-Sales Service:
tel.
0039/039/60.88.213
e-mail
assistenza@pegperego.it
pegperego.com
- 11 -
Peg-Pérego S.p.A. is an ISO 9001 certified
company. This certification is a
guarantee for customers and consumers
of the transparency and trustworthiness
of the company's procedures and
working methods.
fax
0039/039/33.09.992
website
www.