HIKOKI ET 36A Instrucciones De Manejo página 4

English
32. The machine does get hot. However, this does not
indicate an abnormality.
Keep the electricity running and operate the internal
fan to cool the machine before carrying it elsewhere.
33. During use, do not pull the cord to move the Box.
Doing so may result in damage.
34. Do not use more that a single cord reel of 30 meters.
Doing so may result in damage.
35. During use, if the machine stops running after the
Box's LED lamp blinks, confi rm the power supply
environment.
36. Do not drag the cord when using or carrying the
machine.
Doing so may tear the cord insulation or break the
cord which could result in electric shock.
37. Do not stretch the cord out any more than required.
When using tools such as gardening clippers or
circular saws, always make sure of the power cord's
position to avoid cutting the cord during operation.
38. To use the AC/DC adapter after it shuts down due to
high temperature, disconnect the box's power plug,
wait for the LED lamp to go out and then reconnect
the box's power plug. If the machine cuts off even after
suffi ciently cooling it off with the built-in fan, discontinue
use as there may be a problem with the machine.
39. Do not use this product near a radio. Doing so could
cause noise from the radio, making it diffi cult to listen
to a broadcast.
40. This is a power source for multi volt products. Do not
use with 18 V products or chargers. Doing so could
result in damage.
41. Overload behavior may diff er when compared with
BSL36B18 battery use.
With the battery where the LED should blink on the
main unit, the LED on the AC/DC adapter may blink
instead.
42. Do not use this product near a pacemaker or other
similar implanted device, which may be aff ected by a
magnetic fi eld produced by this product.
PRECAUTIONS FOR AC/DC ADAPTER
The adapter equips with the protection function to stop
the output. In the cases of 1 to 2 described below, when
using this product, even if you are pulling the switch, the
motor may stop. This is not the trouble but the result of
protection function.
1. If the tool is overloaded, output may stop. In this case,
release the switch of tool and eliminate causes of
overloading.
2. If the adapter is overheated under overload work,
output may stop.
In situations like this, discontinue use of the adapter
and detach it from the tool. Allow the adapter to cool
in a location such as a shaded area with good air
circulation. After that, you can use it again.
NAMES OF PARTS (Fig. 1 – Fig. 2)
Outlet plug
1
AC cable
2
Error lamp
3
Box
4
DC cable
5
Ventilation holes
6
Error lamp
7
Adapter
8
Terminal
9
Latch
0
Power lamp
!
Professional 36V
products compatible
@
with multi volt battery
Product not compatible
#
with multi volt battery
SYMBOLS
WARNING
The following show symbols used for the
machine. Be sure that you understand their
meaning before use.
ET36A: AC/DC Adapter
To reduce the risk of injury, user must read
instruction manual.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic
equipment and its implementation in
accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling facility.
Weight
(According to EPTA-Procedure 01/2003)
kg
Prohibited action
Warning
APPLICATION
DC power supply for professional 36V product compatible
with multi volt battery
SPECIFICATION
Model
Output voltage
Power input
Operating
temperature range
Available cordless
products*
1
Weight
*1: For details, see our general catalog or other related
information.
MOUNTING AND OPERATION
Action
Removing and inserting the
adapter
4
ET36A
36 V
1010 W
-10°C – 35°C
Professional 36V products
compatible with multi volt battery
Adapter : 0.8 kg
Box : 1.2 kg
Figure
2
Page
2