Publicidad
Idiomas disponibles
Idiomas disponibles
4. Using the wire nuts provided, make the following
electrical connections, then wrapping and securing
each connection with electrical tape:
a. Connect all white (neutral) wires together, from
house side, fixture, and motion sensor.
b. Connect black wire(s) from fixture to red wire
(load) from motion sensor.
c. Connect black wire from house side to black wire
from motion sensor (Fig. 3).
5. Attach fixture to the junction box according to
instructions provided with your light fixture
(purchased separately).
6. Follow any and all other instructions provided with
your light fixture to complete the hardware portion
of this installation.
7. Turn on power at main fuse /breaker box.
OPERATING YOUR FIXTURE
1. Set dial to "TEST" (Fig. 4).
2. Turn the arrow on the SENSITIVITY knob to a
middle point between "+" and "–".
3. Turn on the power to fixture. Allow fixture to warm
up approximately 40 seconds before testing.
4. Aim sensor head toward desired detection area,
maintaining a 5° down angle to allow moisture
to drain.
NOTE: Maintain air spacing between lamps and sensor
head, at least 2 in. Make sure sensor head is positioned
with control switches facing towards the ground.
5. Walk through the detection zone at the farthest
distance you want your detector to detect motion.
6. Adjust the SENSITIVITY knob until you get desired results. For more range, aim sensor
slightly upward. For less range, aim sensor head slightly downward. Lights will turn
OFF 4 seconds after motion stops.
7. Set dial to desired time setting. The higher the time setting, the longer the lamps will be
ON. (Maximum time is 12 minutes.)
NOTE: Decreasing the SENSITIVITY will decrease the distance the unit can detect.
TROUBLESHOOTING
Light does not
No power to the fixture.
come on with
motion at night.
Bulb is faulty.
Surrounding external
ambient light is too
bright. (If so, the unit
may think it is daytime.)
Wiring to the unit
is loose.
Light comes on
There is motion in the
for no apparent
detection zone.
reason at night.
Light stays
There is motion in the
on at night
detection zone.
and does not
turn off.
Unit is in Dusk-to-Dawn
mode (if there is
no motion).
Fig. 3
Junction
White
B
box
Light
fixture
Red
B
Black
B
Fig. 4
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
• Replace bulb.
• Re-aim the head.
• Relocate or reposition the unit away from
the light.
TURN OFF POWER BEFORE CONTINUING
• Check wiring; reconnect if necessary
using wire nuts (E) provided.
• Make sure the sensor is not picking
up moving objects such as trees,
traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard
to prevent sensor from detecting
motion. If the light stays off, something
in the detection zone is triggering the
sensor.
*If the light stays on with the sensor lens
covered, contact customer service.
• Reduce sensitivity.
• Reposition the sensor.
• Make sure the sensor is not picking up
moving objects such as trees, traffic, etc.
• Reduce sensitivity.
• Reposition the sensor.
• Turn the light switch to the OFF
position for 40 seconds, and then turn
back to the ON position. This will send
the unit back into the "Auto" mode.
Light
The light given from
continuously
the unit's own lamp
blinks on and
is affecting the
off at night.
motion sensor.
Light is on
The controls on
during the day.
the bottom of the
motion sensor are
in "TEST" mode.
The motion detector
is shadowed.
Cannot activate
Surrounding external
Dusk-to-Dawn
ambient light is too
mode at night
bright. (If so, the unit
(override).
may think it is daytime.)
Not enough time is
allowed to enter the
Dusk-to-Dawn mode.
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser's receipt or
other proof of date of original purchase acceptable to Eaton. This is required before warranty
performance shall be rendered.
This warranty does not apply to Eaton products that have been altered or repaired or that
have been subjected to neglect, abuse, misuse or accident (including shipping damages). This
warranty does not apply to products not manufactured by Eaton which have been supplied,
installed, and/or used in conjunction with Eaton products. Damage to the product caused by
replacement bulbs or corrosion or discoloration of brass components are not covered by this
warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED
WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF COOPER LIGHTING PRODUCTS GIVING RISE TO A CLAIM. NO
LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail ConsumerProducts@eaton.com and include the following
information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused.
Eaton is not responsible for merchandise damaged in transit. Repaired or replaced products
shall be subject to the terms of this warranty and are inspected when packed. Evident or
concealed damage that is made in transit should be reported at once to
the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Eaton are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@eaton.com.
Printed in China
2
• Re-aim the lamp.
• Reposition motion sensor.
• Change dial setting (not "TEST" mode).
• Reposition motion sensor.
• Re-aim the head.
• Relocate or reposition the unit away
from the light.
• Turn power OFF and ON twice within
3 seconds.
Publicidad
