Oster 6640 Manual De Instrucciones página 4

M -B
I N I
M -B ® Jars, 8-ounce (250 ml) or 30-ounce (950 ml), are available as accessories and are not
INI LEND
normally included with your Blender. For proper assembly and tightening instructions, see directions
above and on previous page. The M -B
INI LEND
in the same container.
DO NOT USE OTHER TYPES OF JARS FOR PROCESSING FOODS. Ordinary jars may break
or unscrew during processing. Do not wash any parts, including container, in an automatic
dishwasher. DO NOT fill M -B ® Jar above MAXIMUM FILL LINE to allow for expansion
INI LEND
of foods while processing. Overfilling may cause the jar to break and could result in injury.
O
ST E R
®
The O M is available as a stand-alone accessory and packaged with an O
STER INCER
Blender (Model 6646 Only). The Mincer is designed to mince virtually all foods.
H U
OW TO SE
Remove Blender Jar and place onto motor base of Blender. Make sure that the
M
INCER
®
O logo faces front, and that the holes under the base match the Blender spikes.
STER
Remove cover by pushing it down and rotating it counterclockwise. Insert the blade, and put
the ingredients to be minced into the container of your O
by pushing it down and rotating it clockwise, making sure that the three locks are correctly
®
secured and that the O logo is in front. For safe operation while using your Blender,
STER
press down on the cover of the ®
O M
STER
®
After using your O M , remove parts and wash each in water.
STER INCER
Dry immediately or let air dry.
H Y O
O W O U R ST E R I Z E R
Your O ® B is a multi-speed appliance which operates on a wide range of speeds
STERIZER LENDER
from very slow to very fast. This range of speeds makes food preparation easy, interesting
and also saves time because your O
STERIZER
In addition, your O ® B has two distinct methods of operation:
STERIZER LENDER
1 – CONTINUOUS run for blending, liquefying and fine chopping and
2 – CONTROLLED CYCLE BLENDING, used for coarse chopping pieces of food,
such as chopped vegetables, nuts or cheeses. There are several different ways of operating the
CONTROLLED CYCLE BLENDING feature but all involve turning the motor "ON" and "OFF"
intermittently. During the "ON" portion of the cycle, food is chopped and tossed away from
the blades. During the "OFF" portion of the cycle, the food is distributed around the blades to make
processing more uniform. IN THIS BOOK, THE CONTROLLED CYCLE BLENDING FEATURE
IS REFERRED TO AS A CYCLE.
N : A cycle consists of operating the Blender for about 2 seconds and then
OTE
allowing the blade to coast to a stop.
® J
LE N D A R S
® Jars allow for the processing and storing of foods
® M
I N C E R
®
M . Replace the cover
STER INCER
during operation.
INCER
® B W
LE N D E R O R K S
® B processes foods in seconds.
LENDER
6
10-S
PEED
Low speeds are Easy Clean, Purée, Chop, Whip and Mix.
High speeds are Grate, Blend, Grind, Liquefy and Ice Crush.
FOR CONTINUOUS OPERATION
Determine whether you want to use "High" or "Low" continuous cycling. Push the "High"
or "Low" button, rest hand on top of container and then push desired "speed" button.
All speed buttons are continuous speed buttons except for Ice, Crush and Mix,
which are controlled cycle buttons (labeled "pulse"). Press "Off" to turn Blender off.
FOR CONTROLLED CYCLE OPERATIONS
®
STER
The "Ice Crush" (high) and the "Mix" (low) buttons are controlled cycle operations.
To use, determine whether you want to use "High" or "Low" controlled cycle operation.
Press "High" or "Low" button accordingly. Rest hand on top of container and then push
button labeled "Ice Crush" (high)/"Mix" (low)/"Pulse". Hold button down for about
2 seconds, then release and allow blades to coast to a stop. Repeat cycles until contents
reach desired consistency. Release of "Pulse" button turns the Blender off.
N : Pulse button can be held for longer than 2 seconds as needed.
OTE
12-S
PEED
Low speeds are Easy Clean, Purée, Cream, Chop, Whip, and Mix.
High speeds are Grate, Blend, Shred, Grind, Liquefy, and Ice Crush.
FOR CONTINUOUS OPERATION
Determine whether you want to use "High" or "Low" continuous cycling. Slide the
"High" or "Low" switch to "High" or "Low", rest hand on top of container and then
push desired "speed" button. Press "Off" to turn Blender off.
FOR CONTROLLED CYCLE OPERATIONS
Determine whether you want to use "High" or "Low" controlled cycle operation.
Slide the "High" or "Low" switch to "High" or "Low". Rest hand on top of container
and push "Pulse" button. Hold button down for about 2 seconds, then release and
allow the blades to coast to a stop. Repeat cycles specified in recipe. Release of
"Pulse" button turns the Blender off.
N : Pulse button can be held for longer than 2 seconds as needed.
OTE
T P
O ROCESS
• Assemble container (See Page 5, Assembling Your Blender).
• Put ingredients into Blender container, cover firmly, and place container into ring
on motor base. (See Page 5, Tightening the Container.)
H T U Y B
O W O S E O U R
F
OOD
7
LE N D E R