Peg-Perego GT3 Instrucciones De Uso página 20

lower the bottom part, as shown in the figure.
42• Turn the disk outwards, and place your drink in
the holder. To clos e the drink holder, carry out
the instructions in reverse order.
ADJUSTABLE HANDLEBAR
43• The handlebar on the stroller is height-
adjustable. To adjust the height of the handlebar,
simultaneously press the side buttons as shown in
the figure and block the handlebar in the desired
position.
BASKET
44• The basket on the stroller has three positions.
A: Regular position.
B: Lower position allows you to use the basket
even when the backrest is completely lowered. By
pressing on the basket, it is easier to fill it without
disturbing the baby.
C: Raised basket allows the rear footboard to be
used.
GANCIOMATIC SYSTEM
The Ganciomatic System is the swift, practical system
that allows one to fasten the following products,
which can be bought separately and are also equipped
with Ganciomatic System, to the stroller, thanks to
Ganciomatic fasteners.
• Primo Viaggio: a car seat with base, it can be
detached from its base (which stays in the car)
and attached to the Ganciomatic fasteners of the
stroller to transport your child without disturbing
him/her.
• Navetta: the comfortable bassinet unit becomes
a carriage when attached to the fasteners of
the stroller. Equipped with a foldable hood and
carrying handle, both the air circulation regulation
system inside the bassinet and the inclination
of the backrest are adjustable from outside. At
home, it rocks like a cradle and, when the stand is
taken away, it becomes a little bed.
GANCIOMATIC HOOKS ON THE STROLLER
45• To raise the Ganciomatic hooks on the stroller, lift
the sack at the corners of the seat.
46• Raise the two Ganciomatic hooks. They will
automatically move outwards.
• To lower the hooks, pull them inward and down.
GT3 + PRIMO VIAGGIO
47• To fasten the car seat to the stroller:
- set the brake on the stroller;
- remove the hood from the stroller;
- completely lower the backrest on the stroller;
- raise the Ganciomatic hooks on the stroller;
- place the car seat, turned towards the adult, on
the stroller and push downward until it clicks into
place.
- Do not remove the front bar of the stroller when
attaching the car seat, and make sure that it is in
its original position.
• See the userʼs manual for instructions on how to
detach the car seat from the stroller.
GT3 + NAVETTA
48• To fasten the Navetta bassinet unit to the stroller,
you must:
- put the brakes on the stroller;
- remove the hood from the stroller;
- lower the backrest of the stroller completely;
- raise the Ganciomatic fasteners on the stroller;
- remove the front bar;
- raise the footrest on the stroller to the highest
possible position;
- hold onto the handle of the Navetta;
- position the Navetta on the Ganciomatic fasteners
of the the stroller, keeping the head end of the
bassinet at the end of the stroller opposite the
handlebar;
- press down with both hands on the sides of the
Navetta until you hear a click.
• To unfasten the Navetta bassinet unit from the
stroller, consult its instruction manual.
REMOVING THE WHEELS
49• To remove the rear wheels, press the button as
shown in the figure and pull the wheels off the
sides of the stroller.
50• To remove the front wheel, press the button under
the footboard and pull the wheel off.
FOLDING UP THE STROLLER
Before folding the stroller up, set the front wheels
to stationary. If the hood is mounted, lower the
braces.
51• To fold the stroller up, press button number 1 (A)
using your right hand.
52• Using your left hand, grab the handle as shown in
the figure. Press button number 2 (B) and lift the
handle (C) to the top notch.
53• After folding the stroller, fasten the safety hook as
shown in the figure.
REMOVABLE LINING
54• To remove the lining from the stroller, unbutton
the sack from the seat and slip it off the
footboard, as shown in the figure.
55• Detach the sack from the armrests, as shown by
the arrows in the figure.
56• Pull the safety belt leg divider up from under the
seat. Unbutton the side tabs from the backrest.
57• Slip the tabs off the backrest as shown in the
figure. Remove the sack and wash it, following the
instructions printed here.
GT3 Naked Chassis
To convert GT3 into a chassis:
58• Place the backrest in the second position and
remove both the side pieces that support the
backrest.
59• Press both buttons at the bottom of the backrest
(Fig. A) while lifting the backrest as shown in
figure B. Before fastening the Navetta bassinet
unit or the Primo Viaggio car seat to the chassis,
pull the rear part of the Ganciomatic base upwards
as shown in figure C.
• To turn the chassis back into a stroller, repeat the
instructions above in reverse order.
THE GANCIOMATIC SYSTEM with
GT3 NAKED CHASSIS
The Ganciomatic system is a practical, fast way
to fasten the Navetta bassinet unit and the Primo
Viaggio car seat – which are both equipped with the
Ganciomatic system - to the GT3 Naked chassis, using
the Ganciomatic hooks.
GANCIOMATIC HOOKS ON THE CHASSIS
• To raise the Ganciomatic hooks on the chassis,
turn them upwards until they click into place, as
shown in the figure.
• To lower the fasteners, turn them the opposite
direction.
GT3 Naked + NAVETTA
60• To fasten the Navetta bassinet unit to the GT3
Naked chassis:
- Set the brake on the GT3 Naked chassis.