Publicidad
Idiomas disponibles
Idiomas disponibles
Attach Drilling Dust Extraction System to Vertical or
Horizontal Surface (Fig. 1, 3, 8, 9)
The dust extraction system (D) has a suction system that allows the unit to be fixed into place
on a vertical or horizontal surface.
1. With the correct drilling head (G, H) fitted and the drilling dust extraction system securely
connected to the dust extractor vacuum, turn the dust extractor vacuum on as instructed in
the dust extractor vacuum instruction manual.
2. Depress and hold the quick release buttons (E) and place the dust extraction system (D) on
surface to be drilled.
NOTE: The suction system will not hold the unit in place on very rough or uneven surfaces.
Secure the dust extraction system in place as shown in figure 9 if drilling on an uneven
horizontal surface.
3. Release the quick release buttons (E) and the dust extraction system will be secured in
place.
4. To make fine location adjustments, depress the quick release buttons (E) and the seal will
release so the unit can be moved or removed from the surface completely.
WARNING: To reduce the risk of injury, DO NOT turn off the dust extractor vacuum before
removing the drilling dust extraction system from the surface as instructed. Turning off the dust
extractor vacuum before removing the drilling dust extraction system from the surface will cause
the drilling dust extraction system to fall from the surface possibly causing injury.
Remove Drilling Dust Extraction System From Surface
(Fig. 1, 3)
WARNING: To reduce the risk of injury, DO NOT turn off the dust extractor vacuum before
removing the drilling dust extraction system from the surface as instructed. Turning off the dust
extractor vacuum before removing the drilling dust extraction system from the surface will cause
the drilling dust extraction system to fall from the surface possibly causing injury.
Depress the quick release buttons (E) on the dust extraction system to remove it from the
surface.
Attach Hole Cleaning Nozzles (Fig. 1, 6, 7)
Hole cleaning is required to expose the full drilled depth and when using certain types of
chemical fixing anchors to ensure maximum adhesion.
1. Select the correct hole cleaning nozzle to be used:
• Hole cleaning nozzle (A): used for small holes 0.32"–0.56" (8–14 mm) in diameter.
• Hole cleaning nozzle (B) used for holes 0.56" (14 mm) in diameter and above.
2. Remove/replace hole cleaning nozzle:
Grip the nozzle (A, B) firmly and pull it from the connection point (J).
Push the nozzle into the connection point (J) until it stops.
3. Push the dust extractor vacuum hose nozzle (K) into the connection point (C) until tight. For
a more secure connection the AirLock connection system may be used.
NOTE: Ensure hose connection is secure.
OPERATION
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the drill and the dust extractor vacuum. Such preventative safety
measures reduce the risk of starting the tool accidentally.
WARNING: For your own safety, read the tool instruction manual before using any accessory.
Failure to heed these warnings may result in personal injury and serious damage to the tool and
the accessory. When servicing this tool, use only identical replacement parts.
NOTE: The amount of dust retained by the dust extractor vacuum is dependent on its filter
system. Refer to the dust extractor vacuum instruction manual for more information.
Drilling (Fig. 1, 8, 9)
1. Complete the Attach Drilling Dust Extraction System to Vertical or Horizontal
Surface procedure. The unit is now ready to use.
2. Place the drill bit into the center of the drilling head (G, H) and proceed to drill as shown.
Hole Cleaning (Fig. 10)
1. Complete the Attach Hole Cleaning Nozzles procedure.
2. Turn the dust extractor vacuum on as instructed in the dust extractor vacuum instruction
manual.
NOTE: Ensure hose connection is secure.
3. Place the hole cleaning nozzle (A, B) into hole to be cleaned.
MAINTENANCE
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the drill and the dust extractor vacuum. Such preventative safety
measures reduce the risk of starting the tool accidentally.
Your drilling dust extraction system has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory operation depends on proper tool care
and regular cleaning.
TO REPLACE THE SUCTION PAD (FIG. 1)
1. Disconnect dust extraction system from dust extractor vacuum.
2. From the underside of unit remove the four screws (S) to release the suction pad (I).
3. Replacement is a reversal of the above.
New suction pads are available from any D
TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
Excessive dust emission
dust extractor vacuum is full
filter of dust extractor vacuum is
blocked
suction channel is blocked
the wrong drill head is selected
Dust extraction system
dust extractor vacuum is full
does not attach to surface
filter of dust extractor vacuum is
blocked
suction channel is blocked
suction pad is damaged
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
CLEAN DUST EXTRACTION ADAPTOR SUCTION CHANNEL (FIG. 1, 11)
1. Depress drilling head release button (F) and remove drilling head (G, H) from dust extraction
system (D).
2. Use the hole cleaning nozzle (A) to remove dirt and dust from the suction channel (P).
3. Reassemble drilling head to dust extraction system.
CLEAN DRILLING HEAD (FIG. 1, 12)
1. Depress drilling head release button (F) and remove drilling head from dust extraction system.
2. Remove cover (Q) from drilling head (G, H) and use the hole cleaning nozzle (A) to remove dirt and dust.
3. Replace cover (Q) on drilling head and reassemble to dust extraction system (D).
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only D
WALT recommended accessories should be used with this product.
E
WALT authorized repair agent.
E
REMEDY
empty the dust extractor
vacuum
clean or replace the filter
clean the suction channel
select the correct drill head
empty the dust extractor
vacuum
clean or replace the filter
clean the suction channel
replace the suction pad
WALT, have not been tested
E
FIG. 1
A
B
G
FIG. 2
G, H
F
D
FIG. 4
D
K
C
FIG. 5
N
C
O
C
O
R
R
D
F
E
H
I
FIG. 3
FIG. 6
A
B
M
L
C
C
S
E
D
J
Publicidad
