Operational Cautions - Hitachi Koki WH 12DM Instrucciones De Manejo

English
2. Check the rotational direction
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the
bit counterclockwise. (See Fig. 11) (The
marks are provided on the body.)
CAUTION
The push button can not be switched while the
impact driver is turning. To switch the push button,
stop the impact driver, then set the push button.
3. Switch operation
When the trigger switch is depressed, the tool
rotates. When the trigger is released, the tool stops.
The rotational speed can be controlled by varying
the amount that the trigger switch is pulled. Speed
is low when the trigger switch is pulled slightly and
increases as the trigger switch is pulled more.
4. Tightening and loosening screws
Install the bit that matches the screw, line up the
bit in the grooves of the head of the screw, then
tighten it.
Push the impact driver just enough to keep the bit
fitting the head of the screw.
CAUTION
Applying the impact driver for too long tightens the
screw too much and can break it.
Tightening a screw with the impact driver at an
angle to that screw can damage the head of the
screw and the proper force will not be transmitted
to the screw.
Tighten with this impact driver lined up straight
with the screw.
5. Number of screws tightenings possible
Please refer to the table below for the number of
screw tightened possible with one charge.
For WH12DM (EB1230HL)
Screw used
Wood screw ø4 x 50
(Soft wood)
Machine screw M8 x 16
For WH9DM (EB930H)
Screw used
Wood screw ø4 x 50
(Soft wood)
Machine screw M8 x 16
These values may vary slightly, according to
surrounding temperature and battery characteristics.
NOTE
The use of the battery EB1230HL and EB930H in
a cold condition (below 0 degree Centigrade) can
sometimes result in the weakened tightening torque
and reduced amount of work. This, however, is a
temporary phenomenon, and returns to normal when
the battery warms up.
9
L R
and
No. of tightenings
Approx. 860
Approx. 1920
No. of tightenings
Approx. 580
Approx. 1540

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work
After use for continuous bolt-tightening work, rest
the unit for 15 minutes or so when replacing the
battery. The temperature of the motor, switch, etc.,
will rise if the work is started again immediately
after battery replacement, eventually resulting in
burnout.
NOTE:
Do not touch the hammer case, as it gets very hot
during continuous work.
2. Cautions on use of the speed control switch
This switch has a built-in, electronic circuit which
steplessly varies the rotation speed. Consequently,
when the switch trigger is pulled only slightly (low
speed rotation) and the motor is stopped while
continuously driving in screws, the components of
the electronic circuit parts may overheat and be
damaged.
3. Tightening torque
Refer to Figs. 16 and 17 for the tightening torque
of bolts (according to size), under the conditions
shown in Fig. 18. Please use this example as a
general reference, as tightening torque will vary
according to tightening conditions.
NOTE
If a long striking time is used, screws will be strongly
tightened. This may cause the screw to break, or
may damage the tip of the bit.
If the unit is held at an angle to the screw being
tightened, the head of the screw may be damaged,
or the specified torque may not be transmitted to
the screw. Always keep the unit and the screw
being tightened in a straight line.
4. Use a tightening time suitable for the screw
The appropriate torque for a screw differs according
to the material and size of the screw, and the
material being screwed etc., so please use a
tightening time suitable for the screw. In particular,
if a long tightening time is used in the case of
screws smaller than M8, there is a danger of the
screw breaking, so please confirm the tightening
time and the tightening torque beforehand.