Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Parts identification 1
A.-ST 3x8mm W/Washer
Screw: This screw is used
to fit the rear grill to the fan
motor cover and is placed
before putting the propeller
on the motor shaft.
Fig. A
A.
B.
C.
Parts identification 2
1. Front grid
2. Back grid
3. Safety grid's fixing locks
4. Fan blades
5. Motor shaft
6. Blades nut.
7. Engine body.
8. Swing pivot
9. Manual operation
Speed/Off/Pilot Light
10. Pilot light/Night light
11. Control panel
12. Telescopic tube
13. Height fixing rings
14. Fixing knob
15. Base
16. Counterweight
17. Washer
18. L screw
19. Wall support attachment
ASSEMBLY INSTRUCTIONS
Fan assembly:
Fig. B
Set the back grid on the motor shaft, make sure thatthe
internal arrow (as it is draw in the enhancement within Fig.
B) points up and the 4 central clips fit. You might push
firmly in order to make them tightly fit. Once the 4 clips
have been set, make sure they are tight (Fig. C).
Take the 3x8 mm W/ Washer
screw (A) from your kit and
screw it with the help of a
Phillips screwdriver over
the cylinder-shaped housing
that is seen at the top of
the grill. (Fig. D)
Fig. E
www.comfortzoneproducts.com
B y C.- M3x20 mm Screw
and M3 Nut : They are used
to adjust the front and rear
grille, these are placed at
the end of assembling the
grilles. (Fig. A)
3.
5.
7.
.8
1.
10.
9.
4.
.14
11.
2.
6.
.13
.19
12.
15.
16.
18.
Fig. C
Fig. D
Fig. F
Set the fan blades correctly on the engine body
and screw the blades nut towards the word
"THIGHTEN" as the arrows show. (Fig. E)
Join the front and back grills together by aligning
the 6 fixing clips and push firmly until a "click"
sound is heard (Fig. F).
Take the M3mm nut (C)
from your kit and place it on
the hex socket at the bottom
of the rear grille (Fig. G),
then take the M3x20 mm
screw from your kit and put
it on the socket on the
bottom of the front grille.
With the help of a Phillips
screwdriver, screw the nut
to secure both racks (Fig.
H).
Mounting the base:
Unscrew the L screw from the telescopic tube washer.
Set the tube inside the base's round space.
.17
Set the counterweight at the bottom of the base.
Set the washer under the counterweight so that the
domed part keeps touching the counterweight.(Fig. I)
Screw clockwise the L screw into the washer hole
holding the telescopic tube until it is firmly tight into
the base. (Fig. J)
Stand assembly:
Screw the height fixing ring counter clockwise and
lift the stand internal tube until it reaches the desired
height. The maximum fan height is 53.15 in.
Screw the height fixing ring clockwise until it is safely
tight in order to fix the fan´s height.
Unscrew the fixing knob and fit the telescopic tube
inside the engine body set (motor, blades and grids).
Make sure to reach the bottom of the base and screw
the fixing knob clockwise until it is firmly adjust.
Assembling the wall support attachment:
S1
S2
By using a 1/4" drill (not included) make two holes
horizontally aligned with 1.57 in of separation (it is not
recommended to install the wall support attachment
on prefabricated walls or not stable walls).
Fig. I
S3
S4
CZST180BS-EU
CZST180WS-EU
Fig. G
Fig. H
Fig. J
S5
3
Publicidad
Tabla de contenido
