Standard Accessories; Prior To Operation - Hitachi FDV16VB Instrucciones De Manejo

Ocultar thumbs Ver también para FDV16VB:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 25
English
Additional rules for impact drills
- Wear ear protection
Exposure to noise can cause hearing loss.
- Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-Load Speed
Capacity:
Steel
Concrete
Wood
Weight (w/o cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

For entire area
(1) Side handle ............................................................... 1
(2) Depth stopper ........................................................... 1
For partial areas
(1) Chuck wrench ........................................................... 1
(For drill chuck with chuck wrench)
(2) Plastic case ................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATION
By combined action of ROTATION and IMPACT:
Boring holes in concrete, marble, granite, tile, and
similar materials.
By ROTATION only:
Boring holes in metals, wood and plastics.
Tightening wood screws.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized con-
forms to the power requirements specified on the
product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4
FDV16VB
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
0 – 2900/min
2900/min
4. Side handle attachment
Attach the side handle to the mounting part.
Rotate the side handle grip in a clockwise direction
to secure it.
Set the side handle to a position that is suited to
the operation and then securely tighten the side
handle grip.
5. Mounting and dismounting of the bit.
For keyless chuck
(1) Mounting the bit
After inserting a driver bit, etc. into the keyless drill
chuck, firmly grasp the ring and tighten the sleeve
by turning it toward the right (in the clockwise
direction as viewed from the front). (See Fig.1)
If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by
turning it toward the left (in the counterclockwise
direction as viewed from the front). (See Fig.1)
NOTE
When the sleeve does not become loose any fur-
ther, fix the side handle to the sleeve. Then, strike
the grip of the side handle to the left in order to
loosen the sleeve,while holding the ring by hand.
(Fig.2)
CAUTION
Do not fix the side handle to the ring of the keyless
chuck because of a risk that doing so may damage
the ring.
For Drill chuck with chuck wrench
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each
of the three holes in turn. (Fig.3)
6. Selecting the appropriate drill bit
When boring concrete or stone:
Use the drill bits for concrete.
When boring metal or plastic:
Use an ordinary metalworking drill bit.
FDV16T
550W*
High
Low
2300/min
13mm
16mm
25mm
1.6kg
FDV16
2900/min

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Fdv 16tFdv 16

Tabla de contenido