Maintenance And Servicing - Bosch GLI 18V-2200 C Professional Manual Original

12 | English
Close the battery cover (3) and then the locking mechanism
of the battery cover (2).
Make sure that the rubber lip is seated correctly when
u
closing the battery cover. Otherwise protection against
dust and splash water will not be ensured.
Setting up
Carefully fold out the stand (5) and place the cordless work-
light on the floor. Ensure that the tripod has a firm footing.
Fastening to the tripod
You can use the tripod mount (7) to screw the cordless
worklight onto a tripod.
Tighten the 5/8" screw. Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure A)
The lamp head (4) is attached to the carrying handle (8).
The lamp head can be set to five different positions using the
carrying handle.
Switching On/Off
To start up the cordless worklight, press the on/off switch
(1).
To switch off the cordless worklight, press the on/off switch
(1) again.
To save energy, only switch the cordless worklight on when
you are using it.
Adjusting the Brightness
Press the on/off switch (1) briefly to switch on the cordless
worklight with maximum brightness. To adjust the bright-
ness in two stages, hold down the on/off switch (1) until the
required brightness is reached.
Temperature-dependent overload protection
When the permitted operating temperature is exceeded, the
cordless worklight initially reduces the brightness before
switching itself off if required for protection. Let the cordless
worklight cool down and then switch the cordless worklight
back on.
Changing the Button Cell (see figure B)
A warning will be displayed in the app before the button cell
is fully used up.
To change the button cell (11), unlock the locking mechan-
ism of the battery cover (2) and fold up the battery cover
(3), see figure B. Unscrew the screw of the battery compart-
ment cover (9) and remove the battery compartment cover
(10). Remove the empty button cell and insert a new button
cell. Make sure that the battery holder is not damaged
when removing the cell. Make sure that the positive pole
of the button cell faces upwards.
Reattach the battery compartment cover with the screw.
Control Via App
The cordless worklight is fitted with a Bluetooth® module
which enables wireless data transfer to certain mobile
devices with a Bluetooth® interface (e.g. smartphone, tab-
let).
1 609 92A 3WZ | (12.04.2018)
In order to control the cordless worklight via Bluetooth®, you
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "My Tools" subitem in the app. The display of
your mobile device will show you all subsequent steps re-
quired to connect the cordless worklight to the device.
The following functions will be available when a connection
has been established with the mobile device:
– Remote control
– Time control
– Grouping several cordless worklights
– Personalisation
– Status check, output of warning messages
– General information and settings
– Management
Practical Advice
Shortly before the cordless worklight switches off because
of an empty battery (13), it will flash three times and shine
with reduced brightness.
Errors – Causes and Corrective Measures
Cause Corrective measures
A Bluetooth® connection cannot be established with the
cordless worklight.
The cordless worklight is not Remove the button cell (11)
emitting a Bluetooth® signal. and battery (13) for 10
seconds.
The cordless worklight cannot be switched on after
wireless charging.
The inductively chargeable Remove the battery (13) for
battery has to be re-initial- 10 seconds.
ised.

Maintenance and Servicing

Maintenance and Cleaning
The light source cannot be replaced. If the light source is de-
fective, the entire cordless worklight has to be replaced.
The cordless worklight is maintenance-free and does not
contain any parts that need to be replaced or maintained.
Only clean the cordless worklight's plastic lens with a dry,
soft cloth to prevent damage. Do not use any detergents or
solvents.
After-sales service and advice on using products
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
Bosch Power Tools