Areas Of Application; On/Off Switch - ALPHA-TOOLS AL 9,6 Manual De Instrucciones

Anleitung AL 9,6 AlphaTools
GB
case of accidental contact, wash the affected
area of skin with soap and water. If battery acids
gets in your eye, rinse out the eye with clear
water for at least 10 minutes and seek a doctor's
advice immediately.
8. Protect the battery charger and its cable from
damage and sharp edges. Have damaged
cables repaired without delay by a qualified
electrician.
9. Check your tool for damage. Repairs may only
be carried out by a qualified electrician.
10. Make sure that the contacts of the battery pack
do not come into contact with other metallic
objects such as nails or screws. There is a risk of
short-circuiting!

Areas of application

This device is intended solely for pumping up vehicle
tires, bicycle tires and blow-up leisure, sports and
beach articles. It is not suitable for large-volume
articles (e.g. rubber dinghies, large airbeds). It is not
intended for industrial use.
Starting up:
Charging the NC battery pack
1. Before you remove or insert the battery, activate
the transport brace (Pos. 3). To do this, slide the
slide button for the transport brace to the left
(lock is closed). Remove the battery pack (Pos.
6) from the handle, pressing the pushlock
buttons (A) at the side to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger (Pos. 11) in
the plug socket and connect the charging cable
to the charging adapter (Pos. 12). The green
LED will illuminate to show that the mains power
is connected to the charging adapter.
3. Plug the battery pack (Pos. 6) in the charging
adapter (Pos. 12). The green LED and the red
LED will illuminate simultaneously and the
battery will start charging. An empty battery
pack requires a maximum charging period of 5
hours. The temperature of the battery pack may
rise slightly during the charging operation. This is
normal.
Important! It does not switch off automatically
when fully charged!
If the battery pack fails to charge, please check
whether there is voltage at the socket-outlet
whether there is good contact at the charging
contacts of the battery station (pos. 12)
8
12.02.2004 12:02 Uhr
If the battery pack still fails to charge, please send
the battery charger and charging adapter
the battery pack
to our customer services department.
To ensure that the NC battery pack provides long
service, you should take care to recharge it promptly.
You must recharge the battery pack when you notice
that the power of the cordless air pump drops.
Never fully discharge the battery pack. This will
cause it to develop a defect!

ON/OFF switch

Insert the charged battery in the handle until it
locks into place. Deactivate the transport brace
(Pos. 3). To do this, slide the slide button to its
position on the right (lock is open).
Switch the device on and off with the ON/OFF
switch (Pos. 4).
Important! A force of over 60N exerted on the
ON/OFF switch may cause the device to switch on in
spite of the transport brace!
Pumping up:
Important! The in-built pressure manometer is not
calibrated. After you have pumped up a tire,
therefore, you will have to check the air pressure
using a calibrated air gauge.
Pumping up vehicle tires
Attach the cordless air pump to the valve either
directly or with the pressure hose (Pos. 7).
Pumping up bicycle tires
To pump up bicycle tires with conventional valves,
screw the adapter (Pos. 8) onto the valve. Attach the
cordless air pump to the adapter or screw the
pressure hose onto the adapter, then pump up the
bicycle tire. For bicycles with car valves, attach the
cordless air pump to the valve either directly or with
the pressure hose (Pos. 7).
Pumping up other objects
To pump up leisure, sports and beach articles, use
the ball adapter (Pos. 9) or airbed adapter (Pos. 10).
In doing so, take care to comply with the instructions
for use of the blow-up object!
Care and maintenance
Always remove the rechargeable battery from the
device before starting any maintenance or repair
Seite 8