Standard Accessories; Prior To Operation - HIKOKI W 4YD Instrucciones De Manejo

f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not allow
for safe handling and control of the tool in unexpected
situations.
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
PRECAUTIONS ON USING AUTOMATIC
SCREWDRIVER
1. This automatic screwdriver is designed for tightening and
loosening screws. Use it only for these operation.
2. One-hand operation is extremely dangerous; hold the
unit fi rmly with both hands when operating.
SPECIFICATIONS
Voltage (by areas)*
Power input
No-load speed
Screw size
Capacity
Screw length
Bit shank size
Weight (without cord)**
* Be sure to check the nameplate on product as it is subject to change by areas.
** According to EPTA-Procedure 01/2014

STANDARD ACCESSORIES

(1) Screw feed attachment ................................................1
(Assembled in main body)
(2) No. 2 Plus Bit ...............................................................1
(Assembled in main body)
(3) Hook ............................................................................1
(4) Sheet ...........................................................................2
(5) Rubber cover ...............................................................1
(6) Plastic case .................................................................1
Standard accessories are subject to change without
notice.
3. Use original bits specifi cally for the automatic screwdriver.
Use no bits other than the original bits specifi cally for the
automatic screwdriver. Use of any other bit can result in
screws sticking out and screw feed malfunctioning.
4. After installing the driver bit, pull lightly out the bit to make
sure that it does not come loose. If the bit is not installed
properly, it can come loose during use, which can be
dangerous.
5. Screw in screws with the main unit held straight.
If the driver is slanted relative to the screw, the screw
head can be damaged and the bit worn. Moreover,
the prescribed torque is not transmitted to the screw,
resulting in screws left sticking out. Place the drive
straight against the screw and screw in.
6. Use the prescribed screws.
Do not use any other screws. They can cause abnormal
work (screws fallen over or sticking out) and break downs
(screw jamming and bit wear).
7. Protect your eyes with protective glasses.
Always wear protective glasses while working. Drilling
scatters plaster powder and tape dust, which are
dangerous if they get into your eyes.
8. Watch out for wires and pipes in walls and ceilings.
When working on fl oors, walls, or ceilings, check for
wires and pipes ahead of time. Work carefully to avoid
shocks and explosions.
9. When the screw feed attachment is removed, always use
the correct driver bit for the screw size.
10. When the screw feed attachment is removed, if the
screwdriver is positioned at an angle against the
tightening screw, the head of the screw may be damaged
or the fi xed tightening force will not transfer to the screw.
Always position the tightening screw and the screwdriver
at a straight angle and then tighten the screw.
(230 V, 240 V)
470 W
4700 min
–1
4 mm
25 – 41 mm
6.35 mm Hex.
1.7 kg
APPLICATIONS
○ Screw driving into indoor gypsum board.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operation
immediately, which could cause a serious accident.
English
9