Publicidad
MIDLAND BT Remote
Advanced Remote Control System
Thank you for purchasing Midland BTRemote wireless remote control system for your Midland intercom.
Midland BTRemote can be fixed on the handlebar of your motorbike to control all the functions of your BTNext, BTX1 and BTX2 intercom devices.
Main features
› Adjustable fixing system
› 3 main function buttons + 2 for volume up and down
› MiniUSB plug for recharging
› Water resistant
Charging batteries
Make sure that the unit is fully charged before use. Charge the unit by inserting
the miniUSB cable in the charging plug (lift the rubber cover to insert the plug).
You can use any USB wall charger like the one in the BTNext, BTX1 or BTX2 box or
use the USB port of your PC. The red LED light will be on during all the charging
time. When the unit is fully charged, the red LED light will be off.
Please note: every time the mini USB recharging plug is inserted (or detached),
the device is automatically turned off. To use it while it is in charge, you should
turn the device on when the plug is already inserted.
Low battery indication
If the red LED is flashing and the unit is not plugged to a charger, it means the
battery is low. Please recharge the unit as soon as possible
Unit and fixing system description
BT Remote description
The BTRemote has five buttons on the front; the main three big buttons are multi
function buttons: the Forward (on the top), the Middle button and the Backward
(on the bottom). The two small rounded buttons on the top are the Volume +
and Volume -
8 - Midland BT Remote
LED Light
Volume up
Volume down
Forward
Middle
Backward
Fixing system description
Midland BTRemote is very easy to fix, just open it and place it on the left handle.
Close it until is quite firm on the handle. To remove it just lift the lock point and
open it.
Interchangeable
rubber spacer
In the box you will find two extra rubber spacers to be replaced in case your
handle has a different size
Switching your Midland BTRemote on and off:
Switching the unit on:
Press and hold "Middle" button down for approximately 3 seconds until the BLUE
indicator lights up.
Switching the unit off:
Press and hold both "Middle" and "Backward" buttons together for approximately
3 seconds until the RED indicator flashes 3 times, thus lessening the chances that
you might turn off the unit accidentally (especially whilst wearing gloves).
Operative mode
Midland BTRemote replicates exactly the same functions as the 5 buttons avai-
lable on the BT Next, BTX1 and BTX2 intercom, therefore you can refer to the
intercom manual.
How to pair the BTRemote
Midland BTRemote can be paired to the following intercoms: BTNext, BTX1 and
BTX2.
First time pairing
The BTRemote is ready to be paired just out of the box:
› Turn on the BTRemote (Press and hold "Middle" button down for 3 seconds,
the blue light will start flashing)
› Turn on the intercom (BTNext, BTX1, BTX2)
› Press any button on the BTRemote ( you must do it within 3 minutes after you
turned on the intercom unit)
The two devices will search for each other and they will automatically pair.
Once the pairing procedure is completed, it does not to be repeated again, becau-
se the BTRemote will automatically recognize the paired unit.
If the pairing procedure fails, just repeat the procedure again. In case the pairing
still does not work, perform first a reset (see the "How to reset the pairing" para-
graph) and than repeat the procedure.
Using the BTRemote
To use the BTRemote, simply switch it on and press any button (make sure that
the intercom is on). This ensures the connection and as soon as the blue light
starts double flashing, you can start using it.
How to reset the pairing
Sometimes you may find it necessary to delete all the pairing references stored in
the BTRemote unit (reset operation):
› Turn off the unit
› Press and hold down the "Middle" and the "Volume +" buttons together, until
the Blue light turn on steady.
› Release the buttons and the blu light will start flashing
Now all the pairing information are deleted and it is possible to start a new pai-
ring session (as explained in the paragraph "First time pairing"):
› While the blu light is flashing, just turn on the intercom unit (BTNext, BTX1,
BTX2)
› Press any button on the BTRemote ( you must do it within 3 minutes after you
turned on the intercom unit)
The two devices will search for each other and they will automatically pair.
Midland BT Remote - 9
Publicidad
