Display And Operating Elements - Siemens OZW672 Serie Instrucciones De Montaje

Web server settings
• The following settings are made depending on the given
application.
• Edit settings: Click the red pencil symbol .
• Settings marked with an asterisk (*): Applies to OZS164.23 only.
13. Select "Home" from primary navigation:
Home > 0.5 OZW672...
Home > 0.5 OZS164...
14. ...> Time of day/date: Time of day/date
15. ...> Settings > Web server: Language
16. ...> Settings > Time of day/date:
Summer time start, Winter time start
17. ...> Settings > Communication > :
Device number, Clock time source
18. ...> Settings > Communication > Ethernet: (see
− IP address: Web server IP address.
− Subnet mask: Generally the same as for the router.
− Default gateway: Router IP address.
− Preferred DNS server: Router IP address.
− Alternate DNS server: Generally empty.
19. ...> Settings > Communication > E-mail:
Address mail server, Port number mail server, E-mail address
sender, Authentification mail server, User name, Password,
Signature line 1...10
20. (*) ...> Settings > Communication > Modem: PIN SIM card,
Transmission protocol
21. (*) ...> Settings > SMS operation: Permitted phone number 1...5,
Password
22. ...> Settings > Message receiver >
Message receiver 1...4: Message receiver 1...4, Fault priority,
Receiver type, E-mail address, Phone number receiver (*),
Message repetition (*)
23. ...> Settings > System report:
Signal time, Message cycle, Priority, Next report
24. ...> Settings > Inputs > Fault input 1...2:
Normal position, Text for: Logic 0 / 1
25. ...> Settings > Faults > Local > Web server: Message triggering
26. ...> Settings > Faults > Local > Fault input 1...2: Fault input 1...2,
Fault status message delay, Fault priority, Message triggering,
Text for: No fault, Text for: Fault
27. ...> Settings > Faults > System: Message triggering
28. ...> Settings > Texts: Name, Name bus device (OZS164... only)
Router settings
• The settings (example, see
server outside the PC network (e.g. via the Internet).
29. NAT/PAT for the Web server must be enabled on the router.
30. Moreover, the DynDNS settings are required on the router, when
the router is operated on a public IP address using a dynamic IP
address.
Local operator station settings
• The settings are required if an operator station (PC) is connected
directly with the Web server via Ethernet.
31. The operator station IP address must be set manually so that it is
on the same subnetwork as the Web server.
en 8 / 8 10.05.2011
10
)
10
) are required to access the Web
G5711 74 319 0703 0 b
Final tasks
32. Unplug USB cable.
33. Switch off message suppression.
− Remove the cover.
− Switch (8) must be set to OFF
− Remount the cover.
34. Press button (6) long (>6 s)
• The Web server sends a system report to the defined message
receivers.
• Communications errors are displayed on the red fault LED
(flashing).
Final on-site check
35. ON LED must be green.
36. Fault LED must be off.

Display and operating elements

11
see Figure
LED displays
1 ON (green/red)
Dark No power.
Steady red Web server starting (operating system).
Flashing red Web server starting (application).
Steady green Web server operational.
2 LPB/BSB A (green)
Dark No bus power.
Lit LPB/BSB operational.
Flashing Communication on LPB/BSB.
3 (LED) B
Dark No function.
4 Fault (red)
Displays faults from the Web server or the connected bus device:
Dark No fault.
Lit Acknowledged fault.
Flashing Unacknowledged fault
5 (LED)
Dark No function.
Operating buttons
The following applies when pressing the buttons:
Short: <2 seconds.
Long: <6 seconds.
6 Remote
Short No function.
Long Sends system report to the configured receiver;
see as well "Button combination".
7 Service button
Short No function.
Long See "Button combination".
Button combination and
Short No function.
Long Reestablishes default state.
Note on "default state":
• All configuration data and settings are reset.
• The device list, plant diagrams, and unsent messages are deleted.
• History data is not deleted.
.
11
(4)
Building Technologies