Repair And Maintenance - Dolmar AB-1816 Manual De Instrucciones

Article 4.
Charging instruction
1. Make sure the battery is full-charged and charge each
time after the use to insure the battery life.
2. Please do not put the battery in a wet place when
charge, the temperature should be 10°C – 40°C
(50°F – 104°F).
3. Do not cover the battery cartridge and charger with
anything when charging and avoid letting liquid and
metal powder inside.
4. If the battery's temperature exceeds 60°C (140°F), it
may lead any trouble in the charger. Please cut off the
power and sent for repair.
5. Keep the battery and charger away from kids.
6. The charger could only be used for this battery.
Article 5.

Repair and maintenance

• Before use, please check if the battery is locked well
and the display works well.
• Please check the connector of the bicycle and battery
box. Remove dirt to avoid any damage.
• Check the tire regularly, otherwise it will affect the
usage range or damage the tire.
• Before use, check the mechanism and other accessory
on time.
• Do not put the bicycle in humidified atmosphere or
some other place which might make the hardware rust.
• Do not put the whole bicycle under rain or insolation for
too long time so as to avoid the controller and
accessory damaged.
• If any problem in the motor, battery and controller,
please sent to the exclusive agent for the maintenance.
• If you feel it a bit heavy to move the backward, it's a
normal status.
• Do not over load on the bicycle so as to avoid damage
the motor and battery.
• It's important to lubricate the bicycle, the front, rear
axle, BB set per year or half a year. Use a special
lubricant for the hub (Recommend to use the clear
gasoline and vesaline lube), if anything wrong, please
send to our agency for the maintenance.
Article 6.
Using instruction for folding parts
1. To assemble the seat
Insert the seat into the support bar, and adjust the
height according to the length of customer's legs, then
fix the bolt.
Please note the insert depth should not see the safety
line, and twisting force of the clamp lock can not be
less than 18 N.m. (Fig. 11)
2. Quick release use
Fasten the screw tightly and push down the lever
toward the pole to adjust the position correctly.
(Fig. 11)
3. To fold the handlebar stem
Push up the self-locking slider down as showed in the
picture a, then push the handle down according to the
picture b. (Fig. 12)
8
Fold the stem down when the hook is opened as
showed in Fig. 12 & 13.
4. To put pedal
By putting the pedal inside, the desired manner for the
bicycle can be achieved. Grip the lever inside the
pedal and push it down to the body side. (Fig. 14)
5. To fold the frame
Stand on the left side of bicycle, and fold the
handlebar stem first, then hold the frame with your left
hand, hold the folding handle and move it to open.
Turn the folding handle as showed in Fig. 13. When
the folding locking buckle is opened, then hold the
frame from two sides and fold the frame toward the left
of frame, and stop folding until the front wheel and
rear wheel is parallel, as showed in Fig. 15 – 17.
Article 7.
Accessories and adjustment
1. The battery controller and motor cannot be removed.
2. To change parts please come to the agency for
change, we do not responsible for the problem which
caused by customer who remove the parts by
themselves.
3. Please use the Dolmar battery AP-183.
4. Brake adjustment.
Check the brake regularly and check as below:
(Fig. 18 – 20)
4.1 Adjust front brake.
4.1.1. As shown in Fig. 18, check the front brake. The
brake will be fully triggered when the brake lever is
gripped to the half-closed position.
4.1.2. As shown in Fig. 19, loosen the screw to loosen or
tighten the brake arms, and make the distance
between the brake broad and the tire 1.5 – 2 mm.
Tighten the screw. If the distance is different,
please keep adjusting the spring until made the
desired distance, is made which meets the 4.1.1
request.
4.2 Adjust the rear brake.
4.2.1. As shown in Fig. 18, check the rear brake as
4.1.1.
4.2.2. See Fig. 20, to adjust brake, as described in 4.1.1
showing adjustment of the front brake, loose the
brake lever then adjust the screw till it touch the
move board, enclasp the brake lever, adjust the
move board and bolt (2 mm). Adjust some times till
rearwheel turns well and brake function works
well. When 1/3 of the brake is frayed, please
change it.
Attention:
Please do not add lubricants on the rear brake. And
please replace brake shoe in the front brake each year, to
avoid shoe abrasion.
Brake maintenance
In order to maintain your bicycle's braking performance, it
is important to perform maintenance on the braking
system.
• Replacing brake cables and housings.
5. Chain adjusting
Adjust as below:
Disassemble the plastic protecting cover of rear axle,
and release two M12 nut. Turn the adjust nut