Technical Characteristics; Standard Equipment - Virutex FP114 Manual De Instrucciones

Safety guidelines during power tool operation
Before commencing operation
• During machining, do not place the workpiece on a
sturdy surface (concrete, steel, stone, etc) - when the
router bit passes through the workpiece, you can dam-
age the router bit and lose control over the power tool.
• Use the router bits whose allowable rotary speed does
not exceed the rotary speed of the power tool spindle.
Observe manufacturer's recommendations for router bits
use. Do not use router bits that do not conform to the
specifications included in the user's manual.
• Use only sharp nondefective router bits. Bended, blunt
or cracked router bits must be replaced.
• The router bit shank diameter must match precisely
with the internal diameter of the power tool collet.
• Never use the router bit if its cutting unit diameter
exceeds the diameter of the hole in the base plate.
• Remove all nails or any other metal objects from
blanks before cutting.
• When making cuts in walls or partitions, it is neces-
sary to find the location of hidden wiring, water-pipes
and gas pipes. Severe injuries may occur as a result of
damaging electric wiring or household utility lines.
During operation
• When turning the power on and during operation,
hold the power tool with both hands by both handles
and keep a steady position, which will allow you to keep
control over the power tool.
• Keep your hands at a safe distance from the rotating
router bit. Remember that when machining a work-
piece, the router bit end occasionally protrudes beyond
the lower part of the workpiece and is not protected
- touching it may cause severe injuries. Never touch the
rotating router bit with your hands.
• Never start the machining until the router bit reaches
its full speed.
• Advance the router bit to the workpiece only with the
power tool turned on, otherwise the router bit may be
pinched in a workpiece, or a recoil and loss of control
over the power tool can occur.
• When processing small blanks, use clamping devices.
If the blanks are too small to be fixedproperly - do not
process them.
• Never remove sawdust while the power tool motor
is running.
• Do not work materials containing asbestos. Asbestos
is considered carcinogenic.
• Avoid stopping an electric tool motor when loaded.
• Avoid overheating your power tool, when using it
for a long time.
• Never operate the power tool over your head level.
After finishing operation
• The power tool may be removed from the workplace only
after it is turned off and the router bit stops completely.
• Decelerating the router bit rotation by inertia using
the spindle keylock is strictly forbidden- this will put
the power tool out of operation and void your right to
the warranty service.
• During operation the router bit runs very hot - do not
touch it until it cools down.
• Cleaning of the workplace after work should be per-
formed by persons equipped with the aforesaid personal
protection means.
Reducing dust exposure
The chemical substances contained in dust
generated in sanding, cutting, sawing,
grinding, drilling and other construction
industry activities may result in cancer,
congenital deficiency or be harmful to
the fertility.
If you work with chemicals take into account:
• The transparent two silicon oxide and other masonry
products in the wall bricks and cement; the chromium
arsenic (CCA) in wood with chemical treatment. The harm
degree of these substances shall depend on the frequent
degree of you carrying out these works. If you want to
reduce the contact with these chemical substances,
please work in the place with ventilation and you shall
use the appliances with safety certificates (such as the
dust mask designed with tiny dust filter).

2. TECHNICAL CHARACTERISTICS

Universal motor..........................................230V 50/60 Hz
Power..............................................................430 W
No-load speed...................................................26000 min
Standard chuck collet.........................................................6 mm
Routing depth...............................................30 mm
Routing depth with trimming head............24 mm
Weight..........................................................................1,5 kg
Weighted equivalent continuous
acoustic pressure level A.........................................87 dBA
Acoustic power level A........................................98 dBA
Uncertainty............................................................K = 3 dBA
Wear ear protection!
Vibration total values...............................a
Uncertainty........................................................K: 1.5 m/s

3. STANDARD EQUIPMENT

Inside the box you will find the following elements:
• Trimmer for fitting hinges FP114
• Parallel square guide (with 2 nuts and regulation knob
and fixing knob)
• Suction nozzle (with 2 screws + 2 nuts)
-1
: < 2.5 m/s
2
h
2
17