FIRST AUSTRIA FA-2421-7 Manual De Instrucciones página 2

1
N
i
2
iNSTRUCTioN MANUAl
FM CloCk RAdio
loCATioN oF CoNTRolS
(see fig. 1)
1. PROJECTION ON/OFF 12. >>/TUNE +/AUTO ON-OFF
2. PROJECTION TIME 180° DISPLAY
3. snOOZE/slEEp/diMMEr/dst 13. VOLUME DOWN/ALARM 1 ON-
OFF sEt
4. ON – OFF RADIO/ALARM OFF
5. DISPLAY 14. VOLUME UP/ALARM 2 ON-OFF
6. alarM 2 indicatOr sEt
7. pM indicatOr 15. SPEAKER
8. STANDBY INDICATOR 16. FOCUS ADJUSTMENT FOR
9. alarM 1 indicatOr PROJECTION UNIT
10. MEMORY/MEMORY+/CLK.ADJ./ 17. FM antEnna
nap 18. BATTERY COMPARTMENT
19. AC POWER CORD
11. <</TUNE -/YEAR/MONTH/DAY/
DISPLAY AUTO CHANGE ON- 20. rating laBEl (BOttOM OF
OFF UNIT)
PoWER CoNNECTioN
Plug the AC power cord to a household outlet AC source. This unit is equipped
with a battery back up system, it requires a 1x3V CR2032 Flat Lithium battery
(Not included). Insert the battery in the battery compartment, making certain
that the positive and negative (+ and -) battery terminals are attached to the
corresponding terminals on the plate in the battery compartment. If an AC
power failure occurs, the clock automatically switches to the battery power
supply, the clock and timer memory continue running. When the AC power
resumes, the clock switches back to AC again.
gETTiNg STARTEd
TiME ANd CAlENdAR MANUAl SETTiNg
Press CLK.ADJ. button (10), in standby mode, and keep depress over 3
seconds to enter time set mode, after enter the setting mode, press CLK.ADJ
button (10) to change the mode cycle as follows:
Normal —> Year —> Month —> Day —> 12/24H —> Real time Hour —>
Real time Min —> Normal
Action (during data adjustment):
• Press <</Tune- button (11) to adjust data backward.
• Press >>/Tune+ button (12) to adjust data forward.
• Keep depress << or >> button for 3 seconds to enable auto forward.
AlARM
SETTiNg AlARM
Press the alarm set button (13/14) during normal mode to show the alarm time.
Afterwards keep depress the alarm set button (13/14) over 2 seconds to enter
the alarm set mode. After enter the setting mode, press the alarm set button
(13/14) to change the mode cycle as follows :
Normal —> AL 1 Hour —> AL 1 Min —> AL 1 weekday Alarm —> AL 1 wake
beep —> AL 1 wake radio —> AL 1 wake radio volume —> Normal
Normal —> AL 2 Hour —> AL 2 Min —> AL 2 weekday Alarm —> AL 2 wake
beep —> AL 2 wake radio —> AL 2 wake radio volume —> Normal
2
Select alarm weekday mode as follows
1-5: Monday to Friday
1-7: Whole week
6-7: Saturday & Sunday
1-1: One day of week
Action (during data adjustment):
• Press <</Tune- button (11) to adjust data backward.
• Press >>/Tune+ button (12) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
ENABlE/diSABlE THE AlARM
Press and hold the "ALARM 1" (13)/"ALARM 2" (14) button to enable or disable
the alarm. Once the alarm is activated, the bell symbol will be appeared on the
display.
AlARM dURATioN ANd SNooZE FUNCTioN:
Alarm Duration – Beep alarm or radio alarm will continue output for 30 minutes
if no key press, then it will stop automatically and wait for same alarm time on
next day.
Action for Snooze:
• During alarming, press Snooze button (3) will enable snooze function, Beep
alarm or Radio alarm will stop.
• Snooze interval is 9 minute (not include second offset)
• Snooze will continue unless press ON/OFF button (4) to alarm off of Buzzer
alarm or Radio Alarm stop automatically after 30 minutes.
display Auto on-off function:
• Press & hold the display auto on-off button (12) for 3 seconds, the LED
display Indicator will light on, the LED display will turn off after 15 seconds
automatically. Press any button to maintain the LED display for 15 seconds.
• Press & hold the display auto on-off button (12) for 3 seconds, the LED
display Indicator will light off to cancel this function.
AUTo CHANgE diSPlAY CoNTENT (see fig. 2)
In radio off mode, press the DISPLAY AUTO CHANGE ON/OFF (11) button
and keep depressed over 3 seconds to enter time AUTO CHANGE DISPLAY
mode. The Year will be displayed and press again to display Month/Day, the
display returns to time display after 5 seconds.
liSTENiNg To RAdio
Press the ON/OFF button (4) to turn the unit on.
Use the Tune+ or Tune- button to select the desired FM station. If you press
and hold the Tune+ or Tune- button for one second, the release, the unit will
automatically scan to the next broadcasting station.
Press the ON/OFF button (4) to turn the radio OFF.
Note: Ensure that the FM antenna is completely unrolled and extended for best
FM reception.
To SET/RECAll THE RAdio PRESETS
1. Press the ON/OFF button (4) to turn the unit ON.
2. Use the Tune+ or Tune- button to select the desired FM station.
3. Press and hold the memory/memory+ button; "P02" will blink in the display.
4. Use the Tune+ or Tune- button to select the desired preset station
(P01-P10).
5. Press the memory/memory+ button again to set the preset.
Repeat steps 2 through 5 to set more presets.
3