Kinetec Linet Eleganza 1 T 52 Manual De Usuario página 7

Safety

Before using Traction Frame, it is essential to have a thorough understanding of this manual. This manual contains instructions for general use and
guarantees improved safety.

The KINETEC system is according to NF EN 60601-2-52 –June 2010. Directive 93/42/CEE from June 14 1993.
®

The KINETEC system must not be used with traction frame components from another company.
®

Before any use, please make sure that the weight of the patient and of the accessories are compatible with the security load of the bed.

Check before each use and each week the fixing of the jaws, the general state of the accessories.

The physician must define the protocol and ensure that it is correctly implemented.

The weights must be positioned outside of the line of the frame ensuring that they do not pose a risk to any person interfacing with the frame.

Do not position weights above the patient.

All functions of the bed should be blocked when using the traction frame to avoid incompatible use with the patient's pathology and / or assembly
performed.

Remove the traction frame when it is not used.

The headboard should always be in place (risk of neck entrapment), however it can be removed for cervical traction and should be repositioned at
the end of the traction.

Improper use may cause injury to the patient or equipment damage.
Assembly

The KINETEC frame should be installed when the bed is in a low position and without patient.
®

Ensure you only use the correct porch- this will be marked with the "T52 – Linet Eleganza 1" label. They mustn't be used with another bed.

Please respect the positioning of the main elements of the frame, as shown against.

When mounting porches, using the screws supplied with the frame in order to secure all (see photo a).

During assembly of the B210 octagonal bar make sure that both double jaws are on the top of porches (see photo b).

When you install the head porch, the grounding continuity is assured by the cable fixed to the head porch "PRT T52" and the bed grounding socket
(see photo c). Attention with positioning the cable of grounding continuity well in order to prevent that it is not detached during the moving of the
bed with the frame. (make sure that the measure of this socket is inferior or equal to 0.1 ohms ( NF EN 6061-2-52).

In order to respect the grounding continuity, you should realise a maximum of 5 connections.

On a electrical bed, please use only the KINETEC
grounding continuity (please refer to the list enclosed)
Using

When handling the bed, make sure no one is in contact with the elements of the bed and frame. This is to prevent entrapment and pinching with all
the moving parts of the bed and frame.

During the using or during the moving of the bed with the frame, make sure that no components are outside of bed frame (bars, accessories).

Make sure that during the moving of the bed or during the handling no outer components can knock against the frame (lighting, TV...).

Do not move the bed with the frame and the patient, but in an emergency situation take care of the obstacles which can provoke weight
vibrations (elevator entrance).

When you move the bed with the frame and the patient please make sure that the frame is in a low position except when contraindicated and in
this case take care of for example the elevator entrance.
Cleaning

Use a DISINFECTANT (PROPANOL/ISOPROPANOL or ALDEHYDE-based solution). Spray the disinfectant on the SURFACES (plastic and metal
components). We advise to pay particular attention to the articulations and on holding back zones like the screws and bolts.

In order to ensure optimal hygiene, you are advised to clean the pads and the frame for each new patient. All the consumables enable hazard-free
disposal. We advise also to change the yellow balls (SP01) with each different patient.

Recommendations to obtain a maximum hygiene of the pads.
Disinfecting of the pads: Washing at 30°C with use of a disaffection solution during the rinsing cycle. Example of product which can be used: Solution
"Baclinge" at 0.125% or "Souplanios" at 0,125% from ANIOS Laboratory. A complete list of distributors in your country is available on request.
Technical specifications

Product
- Medical terms class 1
- Anodising aluminium tubular and epoxy aluminium jaw

Environment
- Storage/transport conditions:
- Operating conditions:
Warranty
The KINETEC warranty is strictly limited to the replacement free of charge or repair in the plant of the component or components found to be
®
defective.
Kinetec SAS guarantees its Traction frames systems for 2 years against all defects of manufacture from the date of purchase by the consumer.
Kinetec SAS is the only organisation able to assess the application of the warranty to its systems.
The warranty will be considered null and void if the device has been used abnormally or under conditions of use other than those indicated in the
user's manual.
The warranty will also be considered null and void in the event of deterioration or an accident due to negligence, inappropriate surveillance or
inappropriate maintenance, or due to transformation of the equipment or an attempt to repair the equipment.
ENGLISH
Before use, please read this document.
components describe as "Equi" (Medical Equipment Potential Equalization) allowing the
®
Temperature: -40 to 70°C / -40 to 160°F
Relative humidity: up to 90%
Room temperature: 10 to 40°C / 50 to 105°F
Relative humidity: up to 80%
7/16