Unpairing Remote Controls And Sensors With The Alarm Unit; Deleting The Remote Control; Deleting The Sensors For One Zone; Change Pincode - CPVan CP3 Manual De Usuario

Your remote control is now paired. Multiple remotes can be connected to any Alarm
unit. Also, the remote control can be linked to multiple Alarm units using the method
described.

Unpairing remote controls and sensors with the Alarm unit

Zones can be reset individually. Doing so allows you to disconnect the sensors for
just that zone. The Alarm unit also can be disconnected from all remote controls (if
you are using more than one).
IMPORTANT: If more than one remote control is used with the Alarm unit: Please
be aware that there is no option to disconnect just one remote control. With this
procedure, all remote controls are unpaired. Please make sure to again pair the
remote controls you wish to continue to use after you unpaired them.

Deleting the remote control

1. Enter pairing mode by long pressing the arm button [
on. All four lights are now on.
2. Now, again long press the arm button [
flash and off. All remote controls have now been disconnected from your Alarm unit.

Deleting the sensors for one zone.

1. Enter pairing mode by long pressing the one of four digital button [
when the Alarm unit is on. The respective light is now on.
2. Now, again long press the respective digital button, 4 Beeps will be heard and the
light will flash and off. The settings for this zone have now been cleared.
Change the pincode
1. Remove battery
2. Press and hold any numbered button( 1-4)
3. Insert batteries
4. Release button while 5 Beeps will be heard and the light will flash and off, again
press the new pincode you want to change( try as many times as needed)
5. then press the arm button[ ], all four lights will flash and off. The code reset is
now completed.

Adjusting the Volume

1. There are four volume level can be adjustment [Mute, Low, Medium, High]
2. Press the digital button [ ],[ ] simultaneously, 1 Beep will be heard into the
setting mode, again press the digital button [
Low, Medium, High], press the arm button [
] when the Alarm unit is
]. 4 Beeps will be heard and the light will
, , , ]
] to adjust the volume from [Mute,
] to exit the setting mode.

Changing the batteries

1. Remote control: The battery can be changed by open the cover on the back of
the remote control. Remove the back panel and replace the battery. The battery type
is CR2032 (3V, Lithium battery).
2. Alarm unit: Slide off the back panel and replace the batteries with 2x AAA size
1.5V Alkaline batteries.
3. Door sensor: Remove the back panel by open the cover and replace the battery
with a new one. The battery type is CR2450 (3V, Lithium battery).

Adding Alarm units, remote controls and sensors

This CPVan alarm system is extremely versatile and flexible. If you have a starter
kit installed, you can add many more CPVan sensors to adapt it to your exact
requirements. You can extend your system with more CPVan Door and Window or
PIR Motion sensors.Up to 10 sensors per zone in total 40 sensors.
Another great feature is that the system can be expanded with more Alarm units
because each sensor can be connected to multiple Alarm units. This allows you to
hear the alarm at multiple places, eg in your living room as well as in your bed room.
Each Alarm unit can be set with different alarm sounds (Siren or Chime) if required.
Adding remote controls is easy. Each alarm unit can be paired with 5 or more
remote controls and each remote control can control multiple Alarm units
simultaneously. This means that each member of your family or team can switch the
system on or off when they require it. Your home will never be unprotected.
IMPORTANT: If you want to add remote controls and sensors, please only select
devices from the CPVan Home Alarm System. Other devices will not be compatible.
You can always ask us at info@cpvans.com if you need advise. We normally
respond within 24 hours.
CPVan Door/Window Sensor
The CPVan Home Alarm System can be extented panded with more Alarm units
because each sensor can be connected to multiple Alarm units. This allows you to
hear the alarm at multiple places, e.g. in your living room as well as in your bed room.
Each Alarm unit can be set with different alarm sounds (Siren or Chime) if required.
CPVan PIR motion detector