Assembling The Heater; Care And Maintenance - Qlima PEP 2021E Instrucciones De Uso

ASSEMBLING THE HEATER

The manufacturer is not responsible for any harm or damage if attention is
not paid to the points described above.
The use of this product and the elements required for that purpose is entirely
at the end user's own risk.
INSTALLATION
Make sure to mount the appliance only on a level, horizontal, firm and stur-
dy underground.
WARNING - this appliance must be connected to an earthed power socket.
The heater is fitted with a supply cable and molded plug, therefore the ter-
minals should not be interfered with. The following points should be consi-
dered when positioning the heater:
• Please observe the minimum safe distance between the heater body and any
inflammable surfaces. (See Fig 1).
• Make sure that the indication of the different switches can be seen from a
distance of >1 mtr
• The heating lights can be vulnerable. Make sure to handle the appliance with
care. Avoid vibrations.
• Never immerse in water/liquids. Risk of death
Assembly
• Step 1: see figure 2: connect the bottom tube with base by screwing them
together.
• Step 2: see figure 3: feed the Power Cord through the base and the bottom
tube, and pull through around 1.75 – 2 m of cable.
• Step 3: see figure 4: connect the middle tube and top tube with bottom pole
by screwing them together.
• Step 4: Place the power cord plug through base, bottom tube, middle tube
and top pole. Connect the power cord plug to the socket in the heater head.
(see figure 5).
Note: make sure the connection of the power cord plugs inside the pole is
firm and cannot easily disconnect! Mount the clip firmly and make sure the
arrow on the clip is pointing upwards.
• Step 5: This step to be done by 2 people!
see figure 6 and figure 7: push the Heater Head onto the Top tube and fix in
position using 2 x 8mm screws
• Step 6 ** PEP 2021E only **: see figure 8: raise or retract the top tube to
the desired height and tighten to the middle tube by screwing knob down.
Before going to step 7, make sure the heater head is in its high position
• Step 7: see figure 9: Make sure the power cord is completely extracted out of
the pole.
Fix the power cord on the base by using the 2 power cord brackets and the 4
pcs M4 Screws.
• Step 8: complete! See figure 10a for PEP2021E and see figure 10b for PEP1021.
• Step 9: Fix the heater by three wedge bolts on the floor (figure 11).
• Step 10: Tightening the screws by spanner (figure 12 - 13).
4
24
OPERATION
Connect the power cable to a suitable socket (refer to rating label) that is located
in a safe, dry area.
• The switch on the heater head is used to control the one heat setting.
(I) for 900w, (II) for 1200W, (I&II) for 2100W.
The 0 = off
• Although the patio heater is shower proof, do not use when raining or in
wet conditions.
• Always disconnect the power cable from the electrical supply, when the patio
heater is not in use
• Dark points may exist on the surface of the heating elements during the first
few minutes after it is turned on. This is normal, and will not affect the per-
formance of the unit.

CARE AND MAINTENANCE

• When disconnected from the electrical supply, clean the outside of the patio
heater with a damp cloth. Never use corrosive or solvent cleaners or immerse
in water.
• Any maintenance or repairs including replacing the halogen tube should only
be carried out by a qualified electrician or by a Qlima recommended service
center.
TROUBLE SHOOTING
If the heater will not operate, please check the following before seeking repair of
service:
• Check if the power cord is plugged into an electrical outlet, if not plug in.
• See step 4: make sure the the power cord connection in the pole is in good
condition.
• Check if electricity to the main fuse is working.
• Make certain the power switches are turned on. If not, choose a setting.
PEP 2021E
Max. Power output/ 2100W
input
Power supply 220-240V / 50 Hz / 1 ph
Power output steps 3 steps: 900 / 1200 / 2100 W
Height adjustable 160 – 205 cm
Current 9.1 A
Weight 14 kg
Radiation range (*) 4.2 m
(*) for reference only
• For PEP2021E only: Use the appliance only in its maximum height, shorten the
pole to 1,6 meter is for storage only.
PEP 1021
2100W
X
9.1 A
14 kg
4.2 m
4
25