BFT CLONIX2 Instrucciones De Uso página 9

2.3) TRC Transmitter
Keys: : Red
Power supply: : 12V Alkaline battery
Range: : 50 / 100 metres
Transmitter versions:
Single-channel, double-channel, four-channel.
3) ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can
interfere with radio reception. In case of insufficient
transmitter range, move the antenna to a more suitable
position.
4) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by
means of the UNIRADIO programmer which allows you to create
installations in the "collective receivers" mode, as well as manage
the complete installation database using the EEdbase software.
5) MANUAL PROGRAMMING
In the case of standard installations where no advanced functions
are required, it is possible to proceed to manual storage of the
transmitters, making reference to programming table A and to the
example for basic programming in Fig.2.
1) If you wish the transmitter to activate output 1, press
pushbutton SW1, otherwise if you wish the transmitter to
activate output 2, press pushbutton SW2.
2) If you wish to obtain functions other than monostable
activation, refer to table A – output activation.
3) When LED DL1 starts blinking, press hidden key P1 on the
transmitter, LED DL1 will remain continuously lit.
Note: Hidden key P1 appears differently depending on the
transmitter model.
For TRC 1-2 / MITTO 2-4, press hidden key P1 (Fig.4).
For TRC 4, the key P1 function corresponds to simultaneously
pressing the 4 transmitter keys or, after opening the battery
compartment, bridging the two P1 points by means of a
screwdriver (Fig.4).
4) Press the key to be memorised on the transmitter, LED DL1
will start blinking again.
5) To memorise another transmitter, repeat steps 3) and 4).
6) To exit the storage mode, wait until the LED is switched off
completely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL
TO THE FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns
the key code to the receiver; this code is necessary in order to
carry out subsequent cloning of the radio transmitters.
5.1) Transmitter storage via radio in self-learning mode (JP4
open)
This mode is used to copy the keys of a transmitter already stored
in the receiver memory, without accessing the receiver.
The first transmitter is to be memorised in manual mode (see
paragraph 5).
a) Press hidden key P1(fig.4) on the transmitter already
memorised.
b) Press key T on the transmitter already memorised, which is
also to be attributed to the new transmitter.
c) Within 10 sec., press key P1 on the new transmitter to be
memorised.
d) Press key T to be attributed to the new transmitter.
e) To memorise another transmitter, repeat the procedure from
step (c) within a maximum time of 10 seconds, otherwise the
receiver exits the programming mode.
INSTALLATION MANUAL
f) To copy another key, repeat from step (a), having waited for
the receiver to exit the programming mode (or after
disconnecting the receiver from the power supply).
Note: with JP4 open, storage can also be carried out in manual
mode.
WARNING: Maximum protection from storage of foreign
codes is obtained by having the JP4 jumper closed and
programming in MANUAL mode or by means of the UNIPRO
mod. programmer (Fig. 3).
6) RADIO-TRANSMITTER CLONING
Rolling-code cloning (JP5 connected)/ Fixed-code cloning
(JP5 open).
Make reference to the UNIRADIO Instructions and the CLONIX
Programming Guide.
7) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS
Make reference to the UNIRADIO Instructions and the CLONIX
Programming Guide.
8) MAINTENANCE
The maintenance of the system should only be carried out by
qualified personnel regularly. The MITTO transmitters are
supplied by two 3V lithium battiers (type CR2016).The TRC
transmitters are powered by a 12V alkaline battery.When replacing
the batteries type CR2016 do not touch the poles with thehands.
Any reduction in the transmitter capacity may be due to the
batteries getting flat. When the led of the transmitter flashes, it
means that the batteries are flat and must be replaced.
9) DISPOSAL
ATTENTION: disposal should only be carried out by qualified
personnel.
Materials must be disposed of in conformity with the current
regulations.
In case of disposal, the system components do not entail any
particular risks or danger. In case of recovered materials, these
should be sorted out by type (electrical components, copper,
aluminium, plastic etc.).
For battery disposal, refer to the current regulations.
The descriptions and illustrations contained in the present
manual are not binding. The Company reserves the right to
make any alterations deemed appropriate for the technical,
manufacturing and commercial improvement of the product,
while leaving its essential features unchanged, at any time
and without undertaking to update the present publication.
ENGLISH
CLONIX/TRC/MITTO - Ver. 05 - 9