Rockford Fosgate Punch Serie Instalación Y Funcionamiento página 3

F
EATURES
Discreet Dual Clamp (DDC™)
Tweeter Mount
Every aspect of the new Tweeter design has been
completely re-engineered to allow for maximum
ease of installation and fitment.This optimized
patent pending design provides concentric
clamping pressure around the perimeter of the
mounting hole.
The "mounting cups" are in fact not "cups" at all,
but rather unobtrusive "clamps" that quickly
and easily mount in a standard 1.75 inch (45mm)
hole saw opening with a single center screw
securing with balanced pressure to both faces
of the mounting surface. From there, the tweeter
simply snaps into place and is secured by a
snap-on trim ring. Removal is easy if needed.
The protective grille on the tweeter is
non-removable and an intergral part of the design.
ICC (Integrated Concealed Crossover)
For the P152-S and P1652-S, the crossover is
integrated into the basket of the mid-bass driver.
This component grade crossover allows for easy
connection of the full component system without
the need for an external crossover. Just connect
the wires from the tweeter to the TWT
terminals at the speaker, see below.
W
IN – Connect from Amplifier
TWT – Connect to Tweeter
P1 Components
Nominal Diameter - inch (mm)
Description
Nominal Impedance (ohms)
Frequency Response (Hz)
Crossover Frequency (Hz)
12dB/octave Butterworth Crossover HP (High Pass)
Voice Coil Diameter - inch (mm)
Fs - Free Air Resonance (Hz)
Qts
Vas - cu. ft. (Liter)
Xmax - inch (mm)
SPL (dB @ 1w/1m)
Power Handling-Watts (RMS / Peak)
Mounting Diameter-inch (mm)
Mounting Depth-inch (mm)
Includes Grille/Trim Ring
Trim Ring Diameter-inch (mm)
Trim Ring Height-inch (mm)
Includes Adapter Plate
See figures on following pages.
IRING
1/4"
3/16"
(0.25")
(0.1875")
P152-S
5.25 (133.35)
2-Way
4
70Hz-22kHz
3.5kHz
1.0 (25.4)
70Hz
0.68
0.19 (5.4)
0.1 (2.5)
87dB
50/100
4.81 (122.21)
1.87 (47.50)
YES
6.22 (158.00)
0.88 (22.34)
5"x7"/6"x9"
P1T-S Crossover Wiring
1. Use illustration for proper connection.
2. Be sure to maintain speaker polarity.
3. Connecting the positive wire to 0dB matches the amplitude of the tweeter to the speaker.
4. Connecting the positive wire to -2dB or -4dB reduces the amplitude of the tweeter -2dB
or -4dB lower than the midrange, (ideal for tweeters located high in door panels and
midranges located low in the kick panel).
P1T-S – System Connection
-4dB
-2dB
0dB
Crossover
Tweeter
3
S
PECIFICATIONS
P1652-S
6.5 (165.10)
2-Way
4
60Hz-22kHz
3.0kHz
HP (High Pass) HP (High Pass)
1.0 (25.4)
60Hz
0.68
0.60 (16.8)
0.14 (3.5)
89dB
60/120
5.57 (141.35) 1.75 (44.40) (Flush Mount)
2.17 (55.00) 0.91 (23.14) (Flush Mount)
YES
6.97 (177.00)
0.83 (21.00)
5"x7"/6"x9"
Specifications subject to change without notice.
From Amplifier
P1T-S
1.0 (25.0)
Tweeter Kit
4
3.5kHz-22kHz
3.0kHz
–
3.5kHz
–
–
–
90dB
60/120
YES
2.10 (53.34)
0.30 (7.66)
NO