Sundstrom SR591 Instrucciones De Uso página 18

1. Introduction
2. Parts
3. Use
4. Maintenance
5. Technical specifications
6. Key to symbols
7. Approvals
1. Introduction
The Sundström SR 591 welding shields are intended for use
individually or together with the Sundström SR 900-system.
For information about the SR 900-system, see the products
user instructions.
The welding shields are designed specifically for protection
against radiation and spatter during welding, flame-cutting
and similar work.
If you feel uncertain about the selection and care of the
equipment, consult your work supervisor or get in touch with
the sales outlet. You are also welcome to get in touch with
the Technical Service Department at Sundstrom Safety AB.
1.1 Warnings/limitations
Warnings
• Change the welding filter immediately if it is found to be
damaged.
• Materials that come into contact with the user's skin may
give rise to allergic reactions if the user is sensitive.
• If the welding shield is equipped with a toughened mineral
glass lens, a protective lens (item 5 in 2.2 Accessories/
Spare parts) should be fitted on the inside of the toughened
mineral glass lens.
• Damaged or scratched protective lens must immediately
be replaced.
• Where the markings on the visor and visor frame are differ-
ent, the lowest applies.
Limitations
• Check that the welding filter have the correct scale number
for your work.
• The welding shield must always be fitted with a protective
lens in addition to the welding filter.
• Always observe the fire safety rules.
2. Parts
2.1 Delivery check
Check that the equipment is complete in accordance with the
packing list, and undamaged.
Packing list
Fig. 1
1. Welding shield
2. User instructions
3. Cleaning tissue
18
Welding shield SR 591
2.2 Accessories / Spare parts
Fig. 2
Item
1. Welding shield SR 591
2. Head harness SR 591
3. Sweatband SR 591, 5 pack
4. Welding filter, shade No. 8, SR 59008
Welding filter, shade No. 9, SR 59009
Welding filter, shade No. 10, SR 59010
Welding filter, shade No. 11, SR 59011
Welding filter, shade No. 12, SR 59012
Welding filter, shade No. 13, SR 59013
Welding filter, EN 3/10, SR 59005
Welding filter, EN 3/11, SR 59006
Welding filter, EN 4/5-13
Welding filter, 4/9-13, SR 59007
5. Outer protective lens SR 591
7. Inner protective lens for auto lens
Inner protective lens for R06-4508
8. Correction lens, dptr 1,0, SR 59014
Correction lens, dptr 1,5, SR 59015
Correction lens, dptr 2,0, SR 59016
Correction lens, dptr 2,5, SR 59017
9. Holder welding filter SR 591
10. Screw SR 591
11. Protective hood
12. Cleaning tissues SR 5226, box of 50
3. Use
3.1 Installation
See also user instructions for SR 900-system.
Welding filter
Fit a welding filter. See section 4.4.3 To change the welding filter.
3.2 Putting the welding shield on and
adjustements
• Raise the visor and put the welding shield on. Fig. 3.
• If necessary, adjust the head harness, see fig. 4.
Height adjustment.
A - how high the welding shield sits on the head.
Angle adjustment between shield and head harness.
B - the angle against the shield.
Space adjustment between shield and head har-
ness.
C - the space to the shield.
Width adjustment of the head harness.
D - adjustment of the width of the head harness.
• Lower the visor. Fig. 5.
EN
Ordering. No.
H06-4312
R06-4303
R06-4304
T06-4001
T06-4002
T06-4003
T06-4004
T06-4005
T06-4006
T06-4007
T06-4008
R06-4508
T06-4009
R06-4008
R06-4009
R06-4509
T06-4010
T06-4011
T06-4012
T06-4013
R06-4306
R06-4305
T06-4014
H09-0401