Descargar Imprimir esta página

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 22
SYMBOLS
The operation manual must be read carefully.
Never dispose of electrical equipment together with household waste.
This machine conforms to CE declarations.
Use full body protective clothes.
Attention! Wear protective gloves.
Safety goggles must be worn.
Attention! Hot surface may cause burns.
Attention! Risk of fire or explosion.
Attention! Harmful fumes, danger of poisoning. Gases and vapours may be hazardous to health.
Welding gases and vapours are released during welding. Inhalation of these substances may be
dangerous to your health.
Use a welding mask with appropriate filter shading.
CAUTION! Harmful radiation of welding arc.
Do not touch part that are under voltage/power.
PLEASE NOTE!
Drawings in this manual are for illustration purposes only and in some details it
may differ from the actual product.
The original operation manual is in German. Other language versions are translations from German.
1. SAFETY OF USE

1.1 GENERAL NOTES

Take care of your own safety and the one of third parties by reviewing and strictly following the
instructions, included in the operating manual of the device.
Only qualified and skilled personnel can be allowed to start, operate, maintain and repair the machine.
The machine must never be operated contrary to its intended purpose.
1.2 PREPARATION OF WELDING WORK SITE
WELDING OPERATIONS MAY CAUSE FIRE OR EXPLOSION
Strictly follow the occupational health and safety regulations applicable to welding operations and make
sure that the woprkplace is equipped with suitable fire extinguisher.
Never carry out welding operations in flammable areas posing the risk of material ignition.
Never carry out welding operations in an atmosphere containing flammable particles or vapours of
explosive substances.
Remove all flammable materials within 12 meters from the welding operations area and if the removal
is not possible, then please cover flammable materials with a fireproof blanket.
Use safety measures against sparks and glowingmetal particles.
Make sure that sparks or hot metal splinters do not penetrate through the slots or openings in the
coverings, shields or protective screens.
Do not weld tanks or barrels that contain or have contained flammable substances. Do not weld in the
vicinity of such containers and barrels.
Do not weld pressure vessels, pipes of pressurised installations or pressure trays.
Always ensure adequate ventilation.
It is recommended to take a stable position prior to welding.
EN
10
Rev. 20.03.2017
1.3 PERSONAL PROTECTION EQUIPMENT
ELECTRIC ARC RADIATION CAN DAMAGE EYES AND SKIN
When welding, wear a clean, fireproof and non conductive clothing without oil marks (leather, thick
cotton), leather gloves, high boots and protective hood.
Before welding, remove all flammable or explosive items, such as propane butane lighters or matches.
Use a face shield (helmet or shield) and eye protection, with a filter featuring a shade level matching
the sight of the welder and the welding current. The safety standards suggest colouring No. 9 (minimum
No. 8) for each current below 300 A. A lower colouring of the shield can be used if the arc is covered
by the workpiece.
Always use approved safety glasses with side protection under the helmet or any other cover.
Use guards for the welding operations site in order to protect other people from the blinding light
radiation or projections.
Always wear earplugs or other hearing aids to protect against excessive noise and to avoid spatter
entering the ears.
Bystanders should be warned to not look at the electric arc.
1.4 PROTECTION AGAINST ELECTRIC SHOCK
ELECTRIC SHOCK CAN BE LETHAL
The power cable must be connected to the nearest socket and placed in a practical and secure position.
Positioning the cable negligently in the room and on a surface which was not checked must be avoided
as it can lead to electrocution or fire.
Touching electrically charged elements can cause electrocution or serious burns.
Electrical arc and the working area are electrically charged during the power flow.
Input circuit and inner power circuit of the devices are also under voltage charge when the power
supply is turned on.
The elements under the voltage charge must not be touched.
Dry, insulated gloves without any holes and protective clothing must be worn at all times.
Insulation mats or other insulation layers, big enough as not to allow for body contact with an object
or the floor, must be placed on the floor.
The electrical arc must not be touched.
It must be checked if the earthing cable is properly connected or the pin is correctly connected to the
earthed socket. Incorrect connection of the earthing can cause life or health hazard.
The power cables must be regularly checked for damages or lack of insulation. Damaged cables must
be replaced. Negligent insulation repair can cause death or serious injury.
The device must be turned off when it is not being used.
The cable mustn't be wrapped around the body.
A welded object must be properly grounded.
The device may only be used in perfect condition.
Damaged device elements must be repaired or replaced. Seat belts must be used when working at
height.
All components of the equipment and the safety equipment must be stored in one place.
When the device is switched on, the handle end must be kept away from the body.
The ground cable must be mounted to the welded element or as close as possible to it (e.g. to a work
table).
THE DEVICE CAN STILL BE UNDER VOLTAGE UPON FEEDER DISCONNECTION
Voltage in the input capacitor must be checked upon turning off the device and disconnecting it from
the power source. One must make sure that the voltage value is equal to zero. Otherwise, the device
elements must not be touched.
Rev. 20.03.2017
EN
11

Publicidad

loading

Este manual también es adecuado para:

S-stud2500