Intended Use; Technical Data - EINHELL TH-TS 1725 U Manual De Instrucciones

Anleitung_TH_TS_1725_U_SPK8__ 24.09.12 14:53 Seite 33

4. Intended use

The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross stop) of
all types of timber commensurate with the machine's
size. The equipment is not to be used for cutting any
type of round wood.
The equipment may only be used for the tasks it is
designed to handle. Any other use is deemed to be a
case of misuse. The user/operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suitable
saw blades (saw blades made of HM or CV) It is
prohibited to use any type of HSS saw blade and
cutting-off wheel. To use the equipment properly you
must also observe the safety information, the
assembly instructions and the operating instructions
to be found in these operating instructions.
All persons who use and service the equipment have
to be acquainted with these operating instructions
and must be informed about the equipment's
potential hazards. It is also imperative to observe the
accident prevention regulations in force in your area.
The same applies for the general rules of health and
safety at work. The manufacturer will not be liable for
any changes made to the equipment nor for any
damage resulting from such changes. Even when the
equipment is used as prescribed it is still impossible
to eliminate certain residual risk factors. The following
hazards may arise in connection with the equipment's
construction and design:
Contact with the saw blade in the uncovered saw
n
zone.
Reaching into the running saw blade (cut
n
injuries).
Kick-back of workpieces and parts of workpieces.
n
Saw blade fracturing.
n
Catapulting of faulty carbide tips from the saw
n
blade.
Damage to hearing if ear-muffs are not used as
n
necessary.
Harmful emissions of wood dust when used in
n
closed rooms.

5. Technical data

AC motor
Power P
Idle speed n
0
Carbide saw blade
Number of teeth
Bench size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Infinite height adjustment
Infinitely adjustable saw blade angle
Dust extraction connector approx. diameter
Weight
Operating mode S6
Rated operating period/rated idle period (4 min. on/6
min off)
To prevent the motor from overheating, only use the
bench-type circular saw as follows:
After an operating period of 4 minutes (S 6 = 40%)
under the permitted load, you must interrupt your
work for a period of 6 minutes in which the machine
can run idle.
Noise emission values
The noise emission values were measured in
accordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors with
a potential influence on the actual immission level at
the workplace include the duration of impact, the type
GB
230 V ~ 50Hz
S6 40% 1700 W
6500 min -1
Ø 250 x Ø 30
24
610 x 445 mm
608 x 250 mm
435 x 320 mm
73 mm / 90°
63 mm / 45°
0 - 73 mm
0° - 45°
36 mm
approx. 27 kg
Idle speed
94.9 dB(A)
3 dB
106.9 dB(A)
3 dB
33